Operating environment
Operating environment temperature *
3
:
0 °C (32 °F) to 40 °C (104 °F)
(Elevation: below 1 400 m (4 593'); [HIGH ALTITUDE MODE]: [OFF])
0 °C (32 °F) to 30 °C (86 °F)
(Elevation: 1 400 m (4 593') ~ 2 000 m (6 562′); [HIGH ALTITUDE MODE]: [HIGH1])
0 °C (32 °F) to 30 °C (86 °F)
(Elevation: 2 000 m (6 562′) ~ 2 700 m (8 858′); [HIGH ALTITUDE MODE]: [HIGH2])
Operating environment humidity:
20% to 80% (no condensation)
Remote
control
Power supply
DC 3 V (battery (AAA/R03 or AAA/LR03 Type ) x 2)
Operating range Approx. 7 m (22'11-5/8") (when operated directly in front of receptor)
Weight 63 g (2.22 ozs.) (including batteries)
Dimensions Width : 44 mm (1-23/32"), Length : 105 mm (4-1/8"), Height : 20.5 mm (13/16")
*1 Measurement, measuring conditions and method of notation all comply with ISO/IEC 21118:2012 international standards.
*2 This is an average value. It may differ depending on individual product.
*3 If the [PROJECTOR SETUP] menu → [LAMP POWER] is set to [NORMAL], [LAMP POWER] will be switched to [ECO] forcibly to protect
the projector when the operating environment temperature becomes 35 °C (95 °F) or higher.
Note
f The part numbers of accessories and separately sold components are subject to change without notice.
r Terminal
<COMPUTER 1 IN> terminal
1 set high-density D-Sub 15 p (female)
RGB signal
0.7 V [p-p] 75 Ω (When G-SYNC: 1.0 V [p-p] 75 Ω)
SYNC/HD
TTL high impedance, automatic positive/negative
polarity compatible
VD
TTL high impedance, automatic positive/negative
polarity compatible
(The SYNC/HD and VD terminals do not support 3 value SYNC.)
YP
B
P
R
signal
Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p-p] 75 Ω
Y/C signal
Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω
<COMPUTER 2 IN /1 OUT>
terminal
1 set, high-density D-Sub 15 p (female)
RGB signal 0.7 V [p-p] 75 Ω (When G-SYNC: 1.0 V [p-p] 75 Ω)
SYNC/HD TTL high impedance, automatic positive/negative
polarity compatible
VD TTL high impedance, automatic positive/negative
polarity compatible
(The SYNC/HD and VD terminals do not support 3 value SYNC.)
YP
B
P
R
signal Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p-p] 75 Ω
<VIDEO IN> terminal 1 set, pin jack 1.0 V [p-p] 75 Ω
<HDMI 1 IN>/<HDMI 2 IN>
terminal
2 sets, HDMI 19 pin, HDCP compatible, Deep Color compatible
Audio signal Linear PCM (Sampling frequency: 48 kHz/44.1 kHz/32 kHz)
<AUDIO IN 1>/<AUDIO IN 2>
terminal
2 sets, M3 stereo mini jack 0.5 V [rms], input impedance 22 kΩ or more
<AUDIO IN 3> terminal 1 set, pin jack x 2 (L-R) 0.5 V [rms], input impedance 22 kΩ or more
<VARIABLE AUDIO OUT>
terminal
1 set, M3 stereo mini jack (monitor output, stereo compatible)
0 V [rms] to 2.0 V [rms] (variable), output impedance 2.2 kΩ or less
<USB A (VIEWER/
WIRELESS)> terminal
1 set, USB connector (type A)
Memory Viewer / Wireless module (Model No.: ET-WML100) compatible
<USB B (DISPLAY)> terminal 1 set, USB connector (type B), only for USB display function
<SERIAL IN> terminal 1 set, D-Sub 9 p, RS-232C compliant, for computer control
<LAN> terminal
1 set, RJ-45, for network connection, PJLink (Class 1) compatible, 10Base-T/100Base-TX
ENGLISH - 131
Chapter 7 Appendix - Specications
To Next Page
Loading...
