TOUCHSCREEN CONTROL FEATURES
Features of the XTR2 Touchscreen Control
• Full-featured easy to use graphical touchscreen interface
for programming, servicing, and diagnostics.
• Non-linear programming no longer requires cycling
through every parameter when programming/servicing.
Buttons and Symbols
NOTE: Not all buttons appear on all screens.
Regeneration Cycle Wheel
• Displays the regeneration cycle step the system is
currently in. The wheel rotates with each step so that the
current step is shown in green.
NOTE: On metered units, the "Treatment" step on the
Regeneration Cycle Wheel will flash when water is
flowing through the unit.
Home
• Displays the Home screen.
Regeneration
• Displays the Regeneration screen, which allows you to
start a regeneration and manually cycle through the
regeneration steps.
Settings
• Displays the Settings screen, which allows you to adjust
commonly used settings. Pressing this button while in the
Settings screen provides access to the Master Settings
screen, which allows you to fully program the valve.
NOTE: Due to the complexity of these settings and the
potential for errors, Master Settings should only be
accessed by your local water professional.
Diagnostics
• Displays the Diagnostic screen, which can assist
in performing maintenance and troubleshooting
performance issues with the valve.
Brightness/Sound
• Displays the Brightness/Sound screen, which allows you
to adjust the backlight of the control screen and allows
you to mute the alarms of the control.
Vacation Mode
• Halts all scheduled regenerations when pressed; press
again to resume normal operation. When Vacation Mode
is on, the 100 day regeneration error will be suspended.
Assistance
• Displays a name and phone number to call for unit
service.
USB Connect
• Allows you to connect the control to a PC via a USB
cable for field programming or download of diagnostic
parameters via PC (Field Programmer application
required).
Screen Navigation Arrows
• Displayed in the upper-left and upper-right corners of
the screen, these arrows allow you to navigate from one
screen to another. NOTE: Settings on previous screen are
not saved unless
is pressed.
Settings Arrows
• These arrows allow you to change the values of certain
settings when programming the control.
Alarm
• Displayed when an alarm has been triggered;
accompanied by an audible alarm. Press to silence the
audible alarm.
Error
• Displayed when an error has occurred. Press to display
the Error screen for more detailed error information.
Advance
• This arrow allows you to advance through cycle steps
during a regeneration.
Reset
• Displayed in the Diagnostics screen to reset Totalizer
and Peak Flow data and in Master Settings to reset
parameters to factory or non-factory settings.
Accept
• Press to save or accept changes in control configuration.
Cancel
• Press to cancel configuration and exit to previous screen
without saving.
8 • FLECK 5800 XTR2 Service Manual
262.634.2386 | greatlakesintl.com
TOUCHSCREEN CONTROL FEATURES
Features of the XTR2 Touchscreen Control
• Full-featured easy to use graphical touchscreen interface
for programming, servicing, and diagnostics.
• Non-linear programming no longer requires cycling
through every parameter when programming/servicing.
Buttons and Symbols
NOTE: Not all buttons appear on all screens.
Regeneration Cycle Wheel
• Displays the regeneration cycle step the system is
currently in. The wheel rotates with each step so that the
current step is shown in green.
NOTE: On metered units, the "Treatment" step on the
Regeneration Cycle Wheel will flash when water is
flowing through the unit.
Home
• Displays the Home screen.
Regeneration
• Displays the Regeneration screen, which allows you to
start a regeneration and manually cycle through the
regeneration steps.
Settings
• Displays the Settings screen, which allows you to adjust
commonly used settings. Pressing this button while in the
Settings screen provides access to the Master Settings
screen, which allows you to fully program the valve.
NOTE: Due to the complexity of these settings and the
potential for errors, Master Settings should only be
accessed by your local water professional.
Diagnostics
• Displays the Diagnostic screen, which can assist
in performing maintenance and troubleshooting
performance issues with the valve.
Brightness/Sound
• Displays the Brightness/Sound screen, which allows you
to adjust the backlight of the control screen and allows
you to mute the alarms of the control.
Vacation Mode
• Halts all scheduled regenerations when pressed; press
again to resume normal operation. When Vacation Mode
is on, the 100 day regeneration error will be suspended.
Assistance
• Displays a name and phone number to call for unit
service.
USB Connect
• Allows you to connect the control to a PC via a USB
cable for field programming or download of diagnostic
parameters via PC (Field Programmer application
required).
Screen Navigation Arrows
• Displayed in the upper-left and upper-right corners of
the screen, these arrows allow you to navigate from one
screen to another. NOTE: Settings on previous screen are
not saved unless
is pressed.
Settings Arrows
• These arrows allow you to change the values of certain
settings when programming the control.
Alarm
• Displayed when an alarm has been triggered;
accompanied by an audible alarm. Press to silence the
audible alarm.
Error
• Displayed when an error has occurred. Press to display
the Error screen for more detailed error information.
Advance
• This arrow allows you to advance through cycle steps
during a regeneration.
Reset
• Displayed in the Diagnostics screen to reset Totalizer
and Peak Flow data and in Master Settings to reset
parameters to factory or non-factory settings.
Accept
• Press to save or accept changes in control configuration.
Cancel
•
Press to cancel configuration and exit to previous screen
without saving.
8 • FLECK 5800 XTR2 Service Manual
TOUCHSCREEN CONTROL FEATURES
Features of the XTR2 Touchscreen Control
• Full-featured easy to use graphical touchscreen interface
for programming, servicing, and diagnostics.
• Non-linear programming no longer requires cycling
through every parameter when programming/servicing.
Buttons and Symbols
NOTE: Not all buttons appear on all screens.
Regeneration Cycle Wheel
• Displays the regeneration cycle step the system is
currently in. The wheel rotates with each step so that the
current step is shown in green.
NOTE: On metered units, the "Treatment" step on the
Regeneration Cycle Wheel will flash when water is
flowing through the unit.
Home
• Displays the Home screen.
Regeneration
• Displays the Regeneration screen, which allows you to
start a regeneration and manually cycle through the
regeneration steps.
Settings
• Displays the Settings screen, which allows you to adjust
commonly used settings. Pressing this button while in the
Settings screen provides access to the Master Settings
screen, which allows you to fully program the valve.
NOTE: Due to the complexity of these settings and the
potential for errors, Master Settings should only be
accessed by your local water professional.
Diagnostics
• Displays the Diagnostic screen, which can assist
in performing maintenance and troubleshooting
performance issues with the valve.
Brightness/Sound
• Displays the Brightness/Sound screen, which allows you
to adjust the backlight of the control screen and allows
you to mute the alarms of the control.
Vacation Mode
• Halts all scheduled regenerations when pressed; press
again to resume normal operation. When Vacation Mode
is on, the 100 day regeneration error will be suspended.
Assistance
• Displays a name and phone number to call for unit
service.
USB Connect
• Allows you to connect the control to a PC via a USB
cable for field programming or download of diagnostic
parameters via PC (Field Programmer application
required).
Screen Navigation Arrows
• Displayed in the upper-left and upper-right corners of
the screen, these arrows allow you to navigate from one
screen to another. NOTE: Settings on previous screen are
not saved unless
is pressed.
Settings Arrows
• These arrows allow you to change the values of certain
settings when programming the control.
Alarm
• Displayed when an alarm has been triggered;
accompanied by an audible alarm. Press to silence the
audible alarm.
Error
• Displayed when an error has occurred. Press to display
the Error screen for more detailed error information.
Advance
• This arrow allows you to advance through cycle steps
during a regeneration.
Reset
• Displayed in the Diagnostics screen to reset Totalizer
and Peak Flow data and in Master Settings to reset
parameters to factory or non-factory settings.
Accept
•
Press to save or accept changes in control configuration.
Cancel
• Press to cancel configuration and exit to previous screen
without saving.
8 • FLECK 5800 XTR2 Service Manual
To Next Page
Loading...
