Perma PRO 250 - Control Buttons; Operation and Control; Preparations; Prior to Operation

permaPROC-12-
5.5 Control Buttons
Therearetwopush-buttonsonthecontrolunit(refertogure8)whichcanbeusedforamenu-guidedchangeof
thesettings.
♦ WiththeMODE/SAVEbutton(refertofigure11)youcanreachtheconfigurationmenu,changethemodeand
savethemodifiedsettingsforfurtheroperation.
♦ WiththeSELECTbutton(refertofigure12)youcandothefollowing:increasedischargeperiod(Days,
Weeks,Months-eachtimeyoupressthebuttonincreasesthedischargeperiodbyonecalendarunit),
changePROLCunitsize,activateMP-6outletsandsetPIN.
6. Operation and Control
6.1 Preparations
♦ Priortotheinstallationofthelubricator,thelubricationpointandthecompleteconnectiontubemustbe
sufficientlypre-lubricatedwiththesamelubricantthatthePROLCunitcontains.Forthis,perma-tecoffers
a400glubricationcartridgeforgreasepresseswiththecorrespondinglubricant(referto”Accessoriesand
SpareParts”).
♦ WheninstallingthepermaPROC,thesuppliedperma-tecmountingdeviceshouldbeused.
♦ WhenconnectingthepermaPROCtoyourcontrolsystem,thesuppliedperma-tecconnectingcableshould
beused.Thisconnectionmayonlybeestablishedbyqualifiedpersonnel.
♦ Thelubricanttubemustbeinstalledandmountedcorrectly.Thelengthofthelubricanttubemaynotexceed
amaximumof5metersandthetubemustbeaperma-tecproduct.
♦ PleasecheckifthethreadofthepermaPROC(G3/8)correspondstotheconnectionthreadofthelubrication
point.Ifthisisnotthecase,youcanorderacorrespondingreducerorotherpartsfromthepermaaccessory
line.
FortheinitialsettingintooperationofapermaPROC,thepumpsysteminthedriveunitispre-lledwithSF04
fromperma’sstandardrangeoflubricants.Anexceptionismadewithregardtolubricantsforthefoodindustry.
Acompletedischargeofthispumpllingisguaranteedafterapprox.10discharges(carryoutadditionaldis-
charges,ifnecessary).
6.2 Prior to Operation
♦ Checkallpartsofthelubricatorforobviousdamages!
♦ IsthenewPROLCunitlledwiththerequiredlubricant?
♦ Istheconnectingcableconnectedtothecontrolsystemofyourequipmentandisthesupplyvoltage
(DC15Vto30V)applied?
♦ Didyouremoveprotectioncover,discandplugfromdriveunit(seechapter1.2)?
♦ Didyouassembleandmountallofthepartscorrectlyandtightly?
PRESS Short Short
Long > 4 sec. until
the display content
changes completely
Long > 4 sec. until
the display content
changes completely
BUTTON
MODE
SAVE
gure11
SELECT
gure12
MODE
SAVE
gure11
SELECT
gure12
FUNCTION
Selection
incurrent
display
Changingof
values
Movestonewmenuand
savesselectedvalues
Returnstooriginalmenu
withoutsavingchanges
chart4,gure11,gure12