Prodigit 3310F Series - Environmental Requirements; Observe Thei; Fig 2-2 Plug-In Installation and Removal

To Next Page

To Previous Page

3310F Series Operation Manual 13

Fig 2-2 Plug-in installation and removal

2-2. Environmental requirements

• Indoor use.

• Measurement Category I.

• Pollution Degree 2.

• Relative Humidity 80% Max.

• Ambient Temperature 0 to +40°C

• Altitude up to 2000m.

• The equipment is not for measurements performed for CAT II, III and IV.

• Transient Overvoltage on the mains supply can be 2500V.

2-3. Observe the International Electrical Symbol listed below.

Warning！Risk of electric shock

Caution！Carefully read and understand the guidance in the operating manual

Before performing any action.

Main Page

Environmental Conditions3
Declaration of Conformity4
Safety Symbols5
Protective Earth (Ground)5
Table of Contents6
Chapter 1 Introduction8
General Description8
Fig 1-1 3310F 60V/30A/150W Power Contour8
Fig 1-2 3311F 60V/60A/300W Power Contour8
Load Module8
Fig 1-3 3312F 250V/12A/300W Power Contour9
Fig 1-4 3314F 500V/12A/300W Power Contour9
Fig 1-5 3315F 60V/15A/75W Power Contour9
Fig 1-6 Constant Current Mode10
Fig 1-7 Constant Resistance Mode10
Fig 1-8 Constant Voltage Mode11
Fig 1-9 Constant Power Mode11
Fig 1-10 Dynamic Wave Form12
Fig 1-11 Rise Time Transition Limitation13
Features14
Standard Accessories14
Specifications16
Table 1-1 3310F Series Specification17
Chapter 2 Installation18
Fig 2-1 Binding Post and Withdraw Handle on the Front Panel of 3310F Series Plug-In18
Installation and Removal of19
Environmental Requirements20
Observe Thei20
Fig 2-2 Plug-In Installation and Removal20
Cleaning21
Power up21
Operating Flow Chart for each Load Module Operation22
Fig 2-3 3310F Series Electronic Load Module Load Condition Setting Flow Chart22
Chapter 3 Operation23
Front Panel Description23
Fig 3-1 Front Panel of 3310F Plug-In Module23
Instructions24
Fig 3-3 an Equivalent Circuit in Terms of the Current Monitor51
Fig 3-4 (Correct) Connections to an Oscilloscope51
Fig 3-5 (Wrong) Connections to an Oscilloscope52
Load Current54
Fig 3-6 Analog Programming Exampl54
Initial Setting of55
Table 3-1 3310F Initialize55
Table 3-2 3311F Initialize55
Table 3-3 3312F Initialize56
Table 3-4 3314F Initialize56
Input Terminal and Wire Consideration57
Table 3-5 3315F Initialize57
Fig 3-7 Hook Terminal y Type Large Size Terminal Connections58
Table 3-6 Stranded Copper Wire Ampere Capacity58
Protection Features59
Chapter 4 Applications61
Local Sense Connections61
Fig 4-1 Local Voltage Sense Connections61
Remote Sense Connections62
Fig 4-2 Remote Voltage Sense Connections62
Fig 4-3 Constant CURRENT Mode Application63
Fig 4-4 Dynamic Load Current with Independent Programmed Rise/Fall Slew Rate64
Constantv66
Fig 4-5 Constant Voltage Mode Application67
Fig 4-6 Constant Resistance Mode Application69
Fig 4-7 CONSTANT POWER MODE APPLICATION72
Fig 4-8 Connection between 3310F Series Plug-In Load and Multiple Output Power74
Fig 4-9 3310F Series Plug-In Module Parallel Operation75
Fig 4-10 Zero-Volt Loading Connection76
Fig 4-11 3310F Series Electronic Load OCP, OPP, SHORT Operation Flow Chart77

Prodigit 3310F Series - Environmental Requirements; Observe Thei; Fig 2-2 Plug-In Installation and Removal

Table of Contents