Prodigit 3310F Series - Chapter 3 Operation; Front Panel Description; Fig 3-1 Front Panel of 3310 F Plug-In Module

To Next Page

To Previous Page

16 PRODIGIT

Chapter 3 Operation

This chapter describes the front panel operation of each 3310F series load module. Please note that the

memory store/recall function and the GPIB/RS-232C/USB/LAN remote programming terms are detailed in

the separate 3300F/3302F/3305F mainframe operation manual.

3-1 Front panel description

The following sketch shows the layout of the front panel of the unit. Please refer to the relevant

Section as indicated by the number assigned to a front panel function.

For example to understand more about the Imonitor function labeled 24 please refer to 3.1.24

Fig 3-1 Front panel of 3310F plug-in module

Main Page

Environmental Conditions3
Declaration of Conformity4
Safety Symbols5
Protective Earth (Ground)5
Table of Contents6
Chapter 1 Introduction8
General Description8
Fig 1-1 3310F 60V/30A/150W Power Contour8
Fig 1-2 3311F 60V/60A/300W Power Contour8
Load Module8
Fig 1-3 3312F 250V/12A/300W Power Contour9
Fig 1-4 3314F 500V/12A/300W Power Contour9
Fig 1-5 3315F 60V/15A/75W Power Contour9
Fig 1-6 Constant Current Mode10
Fig 1-7 Constant Resistance Mode10
Fig 1-8 Constant Voltage Mode11
Fig 1-9 Constant Power Mode11
Fig 1-10 Dynamic Wave Form12
Fig 1-11 Rise Time Transition Limitation13
Features14
Standard Accessories14
Specifications16
Table 1-1 3310F Series Specification17
Chapter 2 Installation18
Fig 2-1 Binding Post and Withdraw Handle on the Front Panel of 3310F Series Plug-In18
Installation and Removal of19
Environmental Requirements20
Observe Thei20
Fig 2-2 Plug-In Installation and Removal20
Cleaning21
Power up21
Operating Flow Chart for each Load Module Operation22
Fig 2-3 3310F Series Electronic Load Module Load Condition Setting Flow Chart22
Chapter 3 Operation23
Front Panel Description23
Fig 3-1 Front Panel of 3310F Plug-In Module23
Instructions24
Fig 3-3 an Equivalent Circuit in Terms of the Current Monitor51
Fig 3-4 (Correct) Connections to an Oscilloscope51
Fig 3-5 (Wrong) Connections to an Oscilloscope52
Load Current54
Fig 3-6 Analog Programming Exampl54
Initial Setting of55
Table 3-1 3310F Initialize55
Table 3-2 3311F Initialize55
Table 3-3 3312F Initialize56
Table 3-4 3314F Initialize56
Input Terminal and Wire Consideration57
Table 3-5 3315F Initialize57
Fig 3-7 Hook Terminal y Type Large Size Terminal Connections58
Table 3-6 Stranded Copper Wire Ampere Capacity58
Protection Features59
Chapter 4 Applications61
Local Sense Connections61
Fig 4-1 Local Voltage Sense Connections61
Remote Sense Connections62
Fig 4-2 Remote Voltage Sense Connections62
Fig 4-3 Constant CURRENT Mode Application63
Fig 4-4 Dynamic Load Current with Independent Programmed Rise/Fall Slew Rate64
Constantv66
Fig 4-5 Constant Voltage Mode Application67
Fig 4-6 Constant Resistance Mode Application69
Fig 4-7 CONSTANT POWER MODE APPLICATION72
Fig 4-8 Connection between 3310F Series Plug-In Load and Multiple Output Power74
Fig 4-9 3310F Series Plug-In Module Parallel Operation75
Fig 4-10 Zero-Volt Loading Connection76
Fig 4-11 3310F Series Electronic Load OCP, OPP, SHORT Operation Flow Chart77

Prodigit 3310F Series - Chapter 3 Operation; Front Panel Description; Fig 3-1 Front Panel of 3310 F Plug-In Module

Table of Contents