Radio Shack PRO-93 - Display Contrast and Data Cloning

49
Special Features
that operate are
FUNC
, / ,
SQUELCH
, and
VOL-
UME
.
Note:
You cannot activate the key lock while you are en-
tering a frequency into a channel.
To turn on the key lock, press
FUNC
then / .
'<P
'<P'<P
'<P
CF:B<;ô
CF:B<;ôCF:B<;ô
CF:B<;ô
appears for about 1 second.
'<Pý CF:B<;ô
'<Pý CF:B<;ô'<Pý CF:B<;ô
'<Pý CF:B<;ô
ap-
pears when you press any key after locking the keypad.
To turn off the key lock, press
FUNC
then / . The
scanner beeps three times and
'<PýLECF:B<;
'<PýLECF:B<;'<PýLECF:B<;
'<PýLECF:B<;
appears.
CHANGING THE DISPLAY CONTRAST
1. Press
MANUAL
.
2. Press
FUNC
then
9
.
1J<ý 1Gó FNEý B<PJý KFý J<K
1J<ý 1Gó FNEý B<PJý KFý J<K1J<ý 1Gó FNEý B<PJý KFý J<K
1J<ý 1Gó FNEý B<PJý KFý J<K
:FEKI8JKô
:FEKI8JKô:FEKI8JKô
:FEKI8JKô
appears.
3. Press
8
88
8
or
9
99
9
to select the contrast.
4. Press
ENTER
to set the display contrast.
CLONING THE PROGRAMMED DATA
You can transfer the programmed data to and from an-
other RadioShack Pro-93 or a Pro-2053 scanner using
an optional connecting cable with
1
/
8
-inch phone plugs
on both ends, (not included) available at your local Ra-
dioShack store.
Follow these steps to clone the data.
1. Turn on both scanners.
2. Connect the connecting cable to each scanner's
PC/
IF
jack.
և(
և(և(
÷á(+*!ý)+ !
+*!ý)+ !+*!ý)+ !
+*!ý)+ !÷ý1
÷ý1÷ý1
÷ý1,ýKFýJ<E;õýI<DFM<ý:89C<ýKF
,ýKFýJ<E;õýI<DFM<ý:89C<ýKF,ýKFýJ<E;õýI<DFM<ý:89C<ýKF
,ýKFýJ<E;õýI<DFM<ý:89C<ýKF
<O@
<O@<O@
<O@Kô
KôKô
Kôý
ýý
ý
appears.
3. Press
8
88
8
.
áFE=@IDýJ<E;ý;8K8åýñæ5
áFE=@IDýJ<E;ý;8K8åýñæ5áFE=@IDýJ<E;ý;8K8åýñæ5
áFE=@IDýJ<E;ý;8K8åýñæ5!/ý,
!/ý,!/ý,
!/ý,I<JJýFK?<I
I<JJýFK?<II<JJýFK?<I
I<JJýFK?<I
B<Pý=FIý*
B<Pý=FIý*B<Pý=FIý*
B<Pý=FIý*+ô
+ô+ô
+ôý
ýý
ý
appears.
4. Press
1
to send the data to the other unit or press
any other key to cancel the operation.