RADWAG AS series Operating Instruction

Name: RADWAG AS series
Brand: RADWAG
Rating: 5 (1 reviews)

75 pages

To Next Page

To Previous Page

13.5.3. Performing second series of measurements

Second series of measurements is continuation of first series and

procedure proceeds in the same way:

Default Chapter3
- Table of Contents3
1 Technical Data6
2 Basic Information8
- Intended Use8
- Inappropriate Use8
- Warranty8
- Monitoring the Metrological Parameters of the Instrument8
- Data Included in this User Manual8
- Staff Training9
3 Transport and Storage9
- Acceptance Check9
- Packaging9
4 Unpacking, Installation and Commissoning9
- Installation and Operation Place9
- Unpacking10
- Positioning11
- Standard Accessories12
- Cleaning12
- Connection to Mains12
- Connection of Additional Equipment12
5 Basic Functions of the Instrument12
6 Keyboard14
7 User Menu15
- Moving in User Menu17
  - Balance Keyboard17
  - Return to Weighing Function17
8 Weighing18
- Choice of Basic Weighing Unit19
- Choice of Weighing Unit (Temporary)20
- Setting Accessibility of Balance Operating Modes20
  - Choice of Modes Quantity Accessible for User21
  - Setting Contents of P6.1 Ffun - ALL Parameters22
9 Main Setting Parameters23
- Setting Level of Filtering24
- Result Confirmation25
- Autozero Function26
- Light off the Last Display Digit27
10 Another Parameters28
- Backlight of Weighing Result28
- Beep" Signal - Reaction on Pressing Key29
- Printout of All Balance Parameters through RS 232 Port29
11 Balance Calibration30
- Balance with Internal Calibration30
- Entering Calibration Menu32
- Calibration Test35
  - Balances with Internal Calibration35
  - Balances with External Calibration36
- Manual Calibration37
  - Internal Calibration37
  - External Calibration38
- Calibration Report Printout38
12 Setting Printouts for Glp Procedures39
- Setting the Contents of Printouts for GLP Procedures40
13 Balance Operating Modes44
- Counting Details of the same Mass45
- Control Referring Mass of Set Standard49
- Control of % Deviation Referring Mass of Standard51
  - Mass of Standard Determined by Its Weighing52
  - Mass of Standard Entered to Balance Memory by User53
- Defining Thickness of Solids and Liquids54
  - Testing Thickness Solids55
  - Testing Thickness of Liquid55
- Pipettes Calibration55
14 F Unctions for Using Rs 23261
- Speed of Transmission61
- Continuous Transmission62
  - Continuous Transmission off in Basic Interval62
  - Continuous Transmission off in Actual Interval63
- Setting Type of Operating for RS 232 Joint64
- Designation of Data Type Sent through RS 232 Joint (Only for Non-Verified Balances)65
- Designation of Minimum Mass for Operating of some Functions66
- Printout to Printer or Computer67
15 Cooperation with Printer or Computer68
- Schedules of Connecting Conductors69
- Printing Data with Date and Time70
- Cooperation with Statistic Printout Kafka SQS70
- Format of Sending Data70
  - Format of Sent Data after Pressing the PRINT Button71
  - Format of Sent Data for Orders Generated from the Computer71
16 Weighing Loads under Balance72
17 List of Orders in Radwag Balances72
18 Error Messages73
19 Additional Equipment74
- Vibration Damping Table74
- Rack for Weighing Load under Balance74
- Set for Defining Thickness of Solids and Liquids74
- Additional Display74
- Computer Software74

Other manuals for RADWAG AS series

User Manual92 pages

Questions and Answers:

Need help?

Do you have a question about the RADWAG AS series and is the answer not in the manual?

RADWAG AS series Specifications

General

Display	LCD with backlight
Maximum Capacity	Varies by model
Readability	Varies by model
Pan Size	Varies by model
Calibration	Internal or external, depending on model
Stabilization Time	≤ 3 seconds
Interface	RS232, USB
Repeatability (Standard deviation)	Varies by model
Linearity	Varies by model
Net Weight	Varies by model
Protection Class	IP 43