How to troubleshoot Raymarine A series Marine Equipment that does not start up?
If your Raymarine Marine Equipment system or part of it doesn't start, first check the relevant fuses and breakers. Also, ensure the power supply cable is in good condition with tight, corrosion-free connections. Finally, verify the power source provides the correct voltage and sufficient current.
What to do if Raymarine A series radar will not initialize?
If the radar on your Raymarine Marine Equipment will not initialize and the Voltage control module (VCM) is stuck in “sleep mode”, check the power connection at VCM. Ensure the voltage at the input is 12 / 24 V, and the voltage at the output is 40 V.
How to troubleshoot a 'No depth reading / lost bottom lock' on Raymarine Marine Equipment?
If your Raymarine Marine Equipment is not showing a depth reading or has lost bottom lock, verify that the transducer has been installed according to its instructions. If the transducer angle is too great, adjust it, as the beam may be missing the bottom. If the transducer has a kick-up mechanism, ensure it hasn't been activated by hitting an object. Check the power supply voltage as close to the unit as possible under load. Inspect the transducer for damage and ensure it is free from debris or fouling.
What causes a 'No Data' or 'No scanner message' on Raymarine Marine Equipment?
If your Raymarine Marine Equipment displays 'No Data' or 'No scanner message', verify that the scanner power supply cable is in good condition and that all connections are secure and free from corrosion. Also, check the relevant fuses and breakers. Ensure the power source provides the correct voltage and sufficient current, using a voltage booster if needed.
What to do if Raymarine Marine Equipment radar will not initialize (Voltage control module (VCM) stuck in “sleep mode”)?
If your Raymarine Marine Equipment radar will not initialize, and the Voltage Control Module (VCM) is stuck in 'sleep mode', check the power connection at the VCM. Ensure the voltage at the input is 12/24V and the voltage at the output is 40V. A poor power connection may be the cause.
How to fix an incorrect speed reading (from DST transducer) on Raymarine Marine Equipment?
To correct an incorrect speed reading from a DST transducer on your Raymarine Marine Equipment, start by checking that the paddle wheel is clean. If that doesn't solve the issue, add a speed offset. If no speed is displayed, ensure the transducer has a speed element or select a transducer that supports speed measurement from the Transducer Set-Up menu.
What to do if my Raymarine A series Marine Equipment product will not boot up (re-boot loop)?
If your Raymarine product is stuck in a reboot loop, the issue might stem from the power supply and connection, so check the solutions for ‘Products does not turn on or keeps turning off’. Another potential cause is software corruption. In that case, try re-flashing the latest software from the Raymarine website. As a last resort on display products, you can perform a ‘Power on Reset’. Be aware that this will erase all your settings, presets, and user data, reverting the unit to factory defaults.
What to do if there is no data or no scanner message on Raymarine A series?
If you're encountering a 'No Data' or 'No scanner' message on your Raymarine marine equipment, begin by checking the radar scanner's power supply. Ensure the cable is in good condition and that all connections are secure and free from corrosion. Check the relevant fuses and breakers. Also, make sure the power source provides the correct voltage and sufficient current, using a voltage booster if necessary.
Why does my Raymarine A series show a “No Fix” GPS status?
If the Raymarine Marine Equipment displays a “No Fix” GPS status icon, it could be due to several reasons. The geographic location or current conditions might be preventing a satellite fix; in this case, check periodically to see if a fix is obtained in better conditions or another geographic location. Alternatively, there may be a GPS connection fault, so ensure that external GPS connections and cabling are correct and fault free. Finally, the external GPS antenna might be poorly positioned, so ensure the GPS antenna has a clear view of the sky.
What to do if Raymarine A series shows no data or scanner message?
If you have no data or are receiving a 'No scanner' message on your Raymarine Marine Equipment, begin by checking the scanner power supply cable to ensure it is sound and that all connections are tight and free of corrosion. Check the relevant fuses and breakers. Ensure the power source provides the correct voltage and sufficient current, using a voltage booster if needed. Verify that the scanner is correctly connected to a Raymarine network switch or SeaTalkhs crossover coupler, as applicable, and check the status of the Raymarine network switch. Make sure SeaTalkhs/RayNet cables are free from damage and the scanner pedestal switch is in the ON position. If a software mismatch between equipment is suspected, contact Raymarine technical support.
General| Display Type | LCD |
|---|---|
| Chartplotter | Yes |
| Display Size | 7" |
| Display Resolution | 800 x 480 pixels |
| GPS | Yes |
| Sonar | Yes |
| Cartography | Navionics, C-MAP |
| Radar Support | Yes |
| Waterproof Rating | IPX6 |
To Next Page
