Specifications
168
9
*1
See p.127 “To adjust the paper size to a size not indicated on the paper size selector”
*2
When copying onto custom size paper, you need to specify vertical and horizontal
dimensions. See “Copying from the Bypass Tray”, Copy Reference.
*3
Select [OHP Sheet] or [Thick Paper] in the display panel. See “Copying from the Bypass
Tray”, Copy Reference.
*4
Placing one sheet at a time is recommended. See “Copying from the Bypass Tray”,
Copy Reference.
*5
When loading paper, make sure the top of the stack is not higher than the limit mark
of the paper tray.
*6
The paper guide is immovable. If you want to change the size of paper placed in this
tray, contact your service representative.
*7
If you want to use thick (128–163 g/m
2
, 34 lb.–43.5 lb.) paper, select [Thick Paper] on
the display panel. See “Copying from the Bypass Tray”, Copy Reference.
*8
With paper longer than 433 mm, misfeeds, jams and creasing may occur. Make sure
that paper is placed correctly so that it feeds in straight.
*9
The horizontal size is 148–432 mm (5.8"–17") when the booklet finisher is installed.
Important
❒ If you use damp or curled paper, a misfeed may occur.
Note
❒ Load paper into the Tray 1-4 with the print side up.
❒ Place paper in the LCT and bypass tray with the print side down.
❒ When using the bypass tray, it is recommended to set the paper orientation to
L.
❒ When loading OHP transparencies, check the front and back of the sheets,
and place them correctly, or a misfeed might occur. Set the paper orientation
to L and select A4L, 8
1
/
2
"×11"K as paper size.
❒ When using OHP transparencies, fan them for each use. If you store the sheets
in the tray, they may adhere and may cause feeding problems.
❒ When copying onto OHP transparencies, remove copied sheets one by one.
❒ If multiple-sheet jams occur, load the paper sheet by sheet.
❒ Postcards should be fed using the bypass tray. Select [Thick Paper] on the dis-
play panel. See “Copying from the Bypass Tray”, Copy Reference.
❒ When copying onto letterhead paper, the paper placing orientation is differ-
ent depends on which function you are using. See p.112 “Orientation-Fixed
Paper or Two-Sided Paper”.
Bypass
tray
*1
*2
Translucent
paper
*4
*5
A3
L
, A4
KL
, A5
KL
,
8"
×
13"
L
A3
L
, 11"
×
17"
L
, 8
1
/
2
"
×
11"
KL
, 5
1
/
2
"
×
8
1
/
2
"
L
40 sheets
OHP transpar-
encies
*3
*4
A4
L
8
1
/
2
"
×
11"
L
20 sheets
Label paper
(adhesive labels)
A3
L
, A4
KL
, A5
KL
,
8"
×
13"
L
A3
L
, 11"
×
17"
L
, 8
1
/
2
"
×
11"
KL
, 5
1
/
2
"
×
8
1
/
2
"
L
1 sheet
LCT (op-
tional)
*5
*6
60-105 g/m
2
(16-28 lb.)
A4
K
, 8
1
/
2
"
×
11"
K
1500
sheets
Tray type Paper type and
weight
Metric version Inch version Paper
capacity
AdonisC3ver2_GBzenF_FM.book Page 168 Friday, May 16, 2003 10:55 AM
To Next Page
Loading...
