1. In a partitioned system, in order to arm a partition in an „instant stay mode”, by users assigned to only one
partition, simply key in a valid user code within one of the previous sequences; the corresponding partition will
instant stay arm.
2. In a partitioned system, in order to arm a partition in an „instant stay mode”, by users assigned to both
partitions, simply key in a valid user code within one of the previous sequences; the zone 1 and 2 LEDs will
flash for 7 second, allowing the user to choose the partition/partitions to be armed, by pressing [1] and/or [2]
keys. The selected partition/partitions will instant stay arm.
„STAY ARMING”
[*][2][User Code] or [STAY][User Code],
where [STAY] is the key labeled „STAY”.
This method is also useful for perimeter protection and it allows the users to remain in the
protected area while the system/partition is “stay armed”, but this time the access through
the delayed zones is allowed, too, for other users. At the end of the exit delay time, after
such an arming mode, the zones which usually are of the perimeter delayed type will maintain
this feature (if they are first violated during arming, they will start the entry delay timer and
will trigger the alarm only if a valid user code isn’t entered until the entry time elapses). Thus,
this arming mode is useful for the system/partition arming during the night, while the users
can stay at home and other users which have own code may came back while the
system/partition is already armed.
While the green READY LED is ON or blinking, in order to arm the system/partition in
„stay mode”, simply key in a valid user code within one of the previous sequences.
For each key pressing, the keypad buzzer will sound a short beep. The user code must have
the right of “stay arming”.
If after entering the last digit of the user code the keypad buzzer is sounding a long rejection
beeps means:
- The user code was not correct; press [#] key and then key in again the user code
within one of the previous sequences.
- The user code hasn’t the right of “stay arming”; enter a user code with this right.
- The user code is entered while the green READY LED is OFF; all perimeter zones which
don’t allow „forced arming” feature must be closed when the system/partition is stay
armed.
- The user code is entered while the green READY LED is blinking but the code hasn’t the
right of force arming; all perimeter zones must be closed when the system/partition
is stay armed by such a user code.
After entering a valid user code within one of the previous sequences, all keypad
LEDs will be ON for a little while and the keypad buzzer will sound 6 acceptance beeps. Then,
the exit delay timer will start and the red ARMED LED will turn slow blinking. In the
same time the control panel will automatically bypass the interior zones (the zones
inside the objective that have the „stay” attribute activated by programming; the zones that
have not the „stay” attribute activated are called perimeter zones).
If the buzzer warnings were enabled by programming, during the exit delay the keypad
buzzer will sound warning beeps.
During the exit delay the yellow SYSTEM LED will blinking in case there are troubles in the system
(„AC power loss”, „low voltage on battery”, „fail to communicate event”, „BELL trouble”, “phone line
trouble” or „system date and hour loss”) and the orange BYPASS LED will be ON in case at least
one interior zone is going to be bypassed by the panel (and/or at least one zone was
previously bypassed by the users); the orange BYPASS LED will turn OFF only when
disarming.
If during any home arming period at least one alarm or trouble occurs in the system, the
SYSTEM LED will start to blink. Because the alarm memory is cleared only upon another
system/partition arming, after at least one alarm occurred, the yellow SYSTEM LED will stop
to blink only upon another system/partition arming.
After the exit delay elapsed, the READY LED will turn OFF and the red ARMED LED will
keep slow blinking until disarming, signaling the system/partition is stay armed. Any
user can get inside the building through the delayed zones and he/she must enter own user
code (1 to 85) until the entry time elapses, in order to disarm the system/partition.
Notes:
1. In a partitioned system, in order to stay arm a partition, by users assigned to only one partition, simply key in a
valid user code within one of the previous sequences; the corresponding partition will stay arm.
To Next Page
Loading...
