ROEL CERBER C82 - Erase the 4 Simultaneous Erasure of All Follow Me Phone Numbers; Programming Session of the System Date and Hour; Online Download (PC Programming Acceptance)

28
SIMULTANEOUS ERASURE OF ALL FOLLOW ME PHONE NUMBERS
[*][7][Master Code][50] or [CODE][Master Code][50],
where [CODE] is the key labeled “CODE”
While the system is within „master user’s programming menu”, to simultaneous erase all
follow me phone number, select the corresponding submenu [50.
The keypad buzzer will sound 6 confirmation beeps and the control panel will go back into
master user’s programming menu.
Any follow me phone number from 1 to 4 can be selected in order to get a new value
or press [#] key to exit the master user’s programming menu.
PROGRAMMING SESSION OF THE SYSTEM DATE AND HOUR
[*][7][Master Code][60][D / D][Mo / Mo][Y / Y][H / H][Mi / Mi][S / S] or
[CODE][Master Code][60][D / D][Mo / Mo][Y / Y][H / H][Mi / Mi][S / S],
where [CODE] is the key labeled “CODE”
While the system is within „master user’s programming menu”, in order to program the
system date and hour, select [60] submenu.
While the system is within „master user’s the system date and hour programming”, the keypad LEDs’ status
will be as follows:
Remarks:
ARMED A LED
ON
SYSTEM LED
Blinking
READY A LED
ON
zone 1, 2 and 3 LEDs
Blinking
Means the system date and hour were programmed during a previous
programming session
Only zone 1 LED
Blinking
Means the system date and hour are not programmed and the control panel is
waiting for the first 2-digit group which represents the day [D / D]
1 and 2 zone LEDs
Blinking
Means the system date and hour is programmed and the control panel is
waiting for the corresponding 2-digit group for month [Mo / Mo], year [Y / Y],
hour [H / H], minutes [Mi / Mi] or seconds [S / S]
1. Programming of the system date and hour can be canceled by pressing the [#]
key.
2. In order to enter the system date and hour programming, the master user should introduce
the format bellow: [D / D][Mo / Mo][Y / Y][H / H][Mi / Mi][S / S]. Each 2-digit group represents the
day [D / D], month [Mo / Mo], year [Y / Y], hour [H / H], minutes [Mi / Mi] and seconds [S / S].
2.1 Once the first 2-digit group corresponding the day [D / D] was entered, the
keypad buzzer will sound 3 beeps and the control panel is waiting for the second 2-
digit group corresponding the month [Mo / Mo].
2.2 Once second 2-digit group corresponding the month [Mo / Mo] was entered, the
keypad buzzer will sound 3 beeps and the control panel is waiting for the third 2-
digit group corresponding the year [Y / Y].
2.3 Once the third 2-digit group corresponding the year [Y / Y] was entered, the
keypad buzzer will sound 3 beeps and the control panel is waiting for the fourth 2-
digit group corresponding the hour [H / H].
2.4 Once the fourth 2-digit group corresponding the hour [H / H] was entered, the
keypad buzzer will sound 3 beeps and the control panel is waiting for the fifth 2-digit
group corresponding the minutes [Mi / Mi].
2.5 Once the fifth 2-digit group corresponding the minutes [Mi / Mi] was entered, the
keypad buzzer will sound 3 beeps and the control panel is waiting for the sixth 2-
digit group corresponding seconds [S / S].
2.6 Once the sixth (the last) 2-digit group corresponding seconds [S / S] was
entered, the keypad buzzer will sound 6 confirmation beeps and the control panel
will go back within „master user’s programming menu”.
2.7 After any digit was pressed, system date and hour setting can be canceled by
pressing the [#] key. After cancellation by pressing the [#] key, the keypad buzzer
will sound 6 confirmation beeps and the control panel will go back within „master
user’s programming menu”, keeping the old value for the system date and hour.
ONLINE DOWNLOAD (PC PROGRAMMING ACCEPTANCE)