To Next Page
R
Ricardo SparksSep 12, 2025
Why is the sound from USB Audio strange on my Roland Synthesizer?
- KKristie JonesSep 12, 2025
If you're experiencing strange sound from USB Audio on your Roland Synthesizer, switch off Center Cancel.
Why is the sound from USB Audio strange on my Roland Synthesizer?
If you're experiencing strange sound from USB Audio on your Roland Synthesizer, switch off Center Cancel.
Why is there no sound from a specific range of keys on my Roland JUNO-Gi Synthesizer?
If there's no sound from a specific range of keys on your Roland Synthesizer, check the key range settings of the Layers in the Live Set.
Why do notes remain sounding when I play the keyboard on my Roland Synthesizer?
If notes remain sounding when you play the keyboard on your Roland Synthesizer, check the system setting “Hold Pedal Polarity”.
Why is there noise and distortion in the recorded sound on my Roland JUNO-Gi Synthesizer?
If you're getting noise and distortion in the recorded sound on your Roland Synthesizer, adjust the level until it is as high as you can get it without causing the PEAK indicator to light red, ensuring the input sensitivity is appropriate. If you hear noise or distortion after bouncing, the track output levels were too high.
Why is there no sound coming from my Roland JUNO-Gi Synthesizer?
There are several reasons why you might not be getting any sound from your Roland Synthesizer. Here are a few things to check: * Ensure that your connected amp or speakers are powered on. * Verify that the volume on any connected devices is appropriately adjusted. * Make sure the [VOLUME] knob on the synthesizer itself isn't set to the minimum level; adjust it as needed. * Confirm that your amp, speakers, or headphones are correctly connected. If you can hear sound through headphones but not your speakers, there may be an issue with your connection cables or your amp/mixer. * Ensure you are using a connection cable that does not contain a resistor.
How to stop my Roland Synthesizer from turning off by itself?
If the power on your Roland Synthesizer turns off by itself, set the system setting “Auto Power Off” to “OFF” if you want the power to remain on constantly.
Why is the effect not applied on my Roland Synthesizer?
If the effect is not being applied on your Roland Synthesizer, check the on/off setting of each effect. Also, ensure each layer’s Output Assign is set to “MFX.” Finally, check the send level to each effect, as the effect won’t be obtained if the send level to that effect is set at 0. Even if the send levels to the effect is set above 0, the effect won’t be applied if the multi-effect output level, chorus level, or reverb level are set to 0. Check each of these settings.
Why are notes broken off on my Roland JUNO-Gi?
If the notes on your Roland Synthesizer are being broken off, reduce the number of Tones you’re using. Increase the voice reserve setting for layers on which you don’t want to allow broken-off notes, as notes will be broken off if the number of voices used simultaneously exceeds 128.
Why does the display backlight turn off by itself on my Roland Synthesizer?
If the display backlight on your Roland Synthesizer turns off by itself, set the system setting “Power Save Mode” to “OFF” if you want the backlight to remain on constantly.
Why can't I record on my Roland JUNO-Gi?
If you're unable to record on your Roland Synthesizer, remove protection from the song. Check the SD card and ensure it is not locked. Use an SD card that has enough free space remaining, and delete unneeded songs. Increase the amount of free space on the SD card by executing the Song Optimize function, which deletes unneeded data from the SD card.
General| Polyphony | 128 voices |
|---|---|
| Parts | 16 parts |
| Keyboard | 61 keys (with velocity) |
| Wave Memory | 128 MB (16-bit linear equivalent) |
| D Beam Controller | Yes |
| Power Supply | AC Adaptor |
| Effects | Multi-effects, reverb, chorus |
| Display | 240 x 64 dots graphic LCD |
| Sequencer | 16-track sequencer |
| Outputs | 2 x 1/4" (L/Mono, R), 1 x 1/4" (phones) |
| USB | USB (audio/MIDI/data transfer) |
| Preset Patches | Over 1, 300 |
| External Storage | SD/SDHC memory card |
| Connectors | MIDI In/Out, USB |
| Weight | 5.7 kg |
| Patches | Preset: 1, 000 + User: 256 |
| Sampling | Not supported |
