114
Chapter 8. Detailed Editing for Patches
Parameters indicated by ( ) can be edited via ZOOM EDIT (p. 97).
Parameter marked with a “
★
” can be controlled using specified MIDI messages.
(Matrix Control, p. 110)
Positive (+) and negative (-) settings for the Depth parameters result in differing kinds of change in pitch and volume. For example, if you set the Depth
parameter to a positive (+) value for one tone, and set another tone to the same numerical value, but make it negative (-), the modulation phase for the two
tones will be the reverse of each other. This allows you to shift back and forth between two different tones, or combine it with the Pan setting to cyclically
change the location of the sound image.
*
If “Struct 1 & 2, 3 & 4” (p. 99) is set to TYPE 02–10, the settings for tone 1 (3) will follow the settings of tone 2 (4). (This is because the outputs of
tones 1 and 2 are combined into tone 2, and the outputs of tones 3 and 4 are combined into tone 4.)
How to Apply the LFO
Parameter
Value Explanation
Fade Mode
Fade Mode
ON <, ON >,
OFF <, OFF >
How the LFO will be applied
* Set this according to your purpose as described in “How to Apply the LFO” (below).
Fade Time
Fade
0–127
Time over which the LFO amplitude will reach the maximum (minimum)
* Set this according to your purpose as described in “How to Apply the LFO” (below).
Key Trigger
OFF, ON
Specifies whether the LFO cycle will be synchronized to begin when the key is pressed (ON) or not (OFF).
Pitch Depth
★
Pitch Depth
-63–+63
How deeply the LFO will affect pitch
TVF Depth
★
Filter Depth
-63–+63
How deeply the LFO will affect the cutoff frequency
TVA Depth
★
Amp Depth
-63–+63
How deeply the LFO will affect the volume
Pan Depth
★
Pan Depth
-63–+63
How deeply the LFO will affect the pan
●
Apply the LFO gradually after the key is pressed
Fade Mode:
ON <
Delay Time:
Time from when the keyboard is played until the LFO begins to be
applied
Fade Time:
Time over which the LFO amplitude will reach the maximum after the
Delay Time has elapsed
●
Apply the LFO immediately when the key is pressed, and then gradually begin to decrease the effect
Fade Mode:
ON >
Delay Time:
Time that the LFO will continue after the keyboard is played
Fade Time:
Time over which the LFO amplitude will reach the minimum after the
Delay Time has elapsed
●
Apply the LFO gradually after the key is released
Fade Mode:
OFF <
Delay Time:
Time from when the keyboard is released until the LFO begins to be
applied
Fade Time:
Time over which the LFO amplitude will reach the maximum after the
Delay Time has elapsed
●
Apply the LFO from when the key is pressed until it is released, and gradually begin to decrease the effect when the key is released
Fade Mode:
OFF >
Delay Time:
Time that the LFO will continue after the keyboard is released
Fade Time:
Time over which the LFO amplitude will reach the minimum after the
Delay Time has elapsed
ZOOM
ZOOM
ZOOM
ZOOM
ZOOM
ZOOM
ZOOM
Note on
high (more)
low (less)
Pitch
Cutoff Frequency
Level
Pan
Delay
Time
Fade Time
Depth
Note on
high (more)
low (less)
Delay Time
Fade Time
Depth
Pitch
Cutoff Frequency
Level
Pan
high (more)
low (less)
Delay
Time
Fade Time
Depth
Note
off
Note
on
Pitch
Cutoff Frequency
Level
Pan
Note on
high (more)
low (less)
Delay
Time
Fade Time
Depth
Note off
Pitch
Cutoff Frequency
Level
Pan
JUNO-STAGE_e.book 114 ページ ２００８年１０月１７日 金曜日 午後１２時２７分
To Next Page
Loading...
