218
MIDI Implementation
❍
Expression (Controller number 11)
Status
2nd byte 3rd byte
BnH 0BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Expression: 00H - 7FH (0 - 127)
* Not received when Rx Expression Tone Receive Expression parameter (PATCH/MISC
or RHYTHM/RECEIVE) is OFF.
* Not received in Performance mode when Rx Expression parameter (PERFORM/MISC)
is OFF.
❍
Hold 1 (Controller number 64)
Status
2nd byte 3rd byte
BnH 40H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
* Not received when Rx Hold-1/Tone Receive Hold-1 parameter (PATCH/CONTROL or
RHYTHM/RECEIVE) is OFF.
* Not received in Performance mode when Rx Hold-1 parameter (PERFORM/MISC) is
OFF.
* When the Redamper Sw parameter (PATCH/MISC) is turned ON, 128 discrete steps are
recognized for the value.
❍
Portamento (Controller number 65)
Status
2nd byte 3rd byte
BnH 41H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
* In Performance mode, the Part Portamento Switch parameter (PERFORM/PART VIEW/
KEY MOD) will change.
❍
Sostenuto (Controller number 66)
Status
2nd byte 3rd byte
BnH 42H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
❍
Soft (Controller number 67)
Status
2nd byte 3rd byte
BnH 43H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
❍
Legato Foot Switch (Controller number 68)
Status
2nd byte 3rd byte
BnH 44H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
* In Performance mode, the Part Legato Switch parameter (PERFORM/PART VIEW/KEY
MOD) will change.
❍
Hold-2 (Controller number 69)
Status
2nd byte 3rd byte
BnH 45H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* A hold movement isn’t done.
❍
Resonance (Controller number 71)
Status
2nd byte 3rd byte
BnH 47H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv= Resonance value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),
* In Performance mode, the Part Resonance Offset parameter (PERFORM/PART VIEW/
OFFSET) will change.
❍
Release Time (Controller number 72)
Status
2nd byte 3rd byte
BnH 48H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Release Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),
* In Performance mode, the Part Release Time Offset parameter (PERFORM/PART
VIEW/OFFSET) will change.
❍
Attack time (Controller number 73)
Status
2nd byte 3rd byte
BnH 49H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Attack time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),
* In Performance mode, the Part Attack Time Offset parameter (PERFORM/PART VIEW/
OFFSET) will change.
❍
Cutoff (Controller number 74)
Status
2nd byte 3rd byte
BnH 4AH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Cutoff value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the Part Cutoff Offset parameter (PERFORM/PART VIEW/
OFFSET) will change.
❍
Decay Time (Controller number 75)
Status
2nd byte 3rd byte
BnH 4BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Decay Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the Part Decay Time Offset parameter (PERFORM/PART VIEW/
OFFSET) will change.
❍
Vibrato Rate (Controller number 76)
Status
2nd byte 3rd byte
BnH 4CH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Rate value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the Part Vibrato Rate parameter (PERFORM/PART VIEW/
VIBRATO) will change.
❍
Vibrato Depth (Controller number 77)
Status
2nd byte 3rd byte
BnH 4DH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Depth Value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the Part Vibrato Depth parameter (PERFORM/PART VIEW/
VIBRATO) will change.
❍
Vibrato Delay (Controller number 78)
Status
2nd byte 3rd byte
BnH 4EH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Delay value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the Part Vibrato Delay parameter (PERFORM/PART VIEW/
VIBRATO) will change.
❍
General Purpose Controller 5 (Controller number 80)
Status
2nd byte 3rd byte
BnH 50H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (PATCH/TVA PARAMETER) of Tone 1 will change.
JUNO-STAGE_e.book 218 ページ ２００８年１０月１７日 金曜日 午後１２時２７分
To Next Page
Loading...
