EasyManuals Logo

Roland R-07 Reference Guide

Roland R-07
46 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #18 background imageLoading...
Page #18 background image
18
Recording
Using the Rehearsal Function
You can use the rehearsal function to automatically set the
appropriate recording level based on the audio that is input
during the specied length of time.
NOTE
You can’t use the rehearsal function if Limiter (p. 16) is “AGC.
1. Press [MENU] to access the “Menu screen, use
[ ]/[ ] to select “Input, and then press [ ].
2. Use [ ]/[ ] to move the cursor to Rehearsal Time
setting, and use [ ]/[ ] to change the setting.
(Default in bold)
Rehearsal Time
Manual
30 sec
1 min
3 min
5 min
3. Press [MENU] twice to return to the main screen.
4. Point the mic toward the source you want to record,
and press [REHEARSAL].
The input level will automatically be set according to the loudest
volume that occurs during the specied Rehearsal Time. At the
same time, the unit will also perform a test to determine the
appropriate sensitivity for the mic. When the setting is completed,
the R-07 will return to the main screen.
If the Rehearsal Time is set to “Manual, press [
] to nish the
rehearsal.
If you’re going to record a musical performance such as an
instrument or vocal, you should play the loudest passage of the
song.
Using the Pre-Rec Function
The R-07 provides a Pre-Rec function that lets you capture the
two seconds of sound that preceded the moment you press [ ].
Even for situations in which youre not sure when the desired
sound will begin, such as when recording outdoors, this function
ensures that you can record without missing the rst moments of
the sound.
1. Press [MENU] to access the “Menu screen, use
[
]/[ ] to select “Recorder, and then press [ ].
2. Use [ ]/[ ] to move the cursor to Pre-Rec
setting, and use [
]/[ ] to change the setting to
ON.
3. Press [MENU] twice to return to the main screen.
Using the Auto Rec Start Function
By using the Auto Rec Start function, you can have recording start
automatically when a specied time has elapsed, or when the
input level exceeds a specied value.
1. Press [MENU] to access the “Menu screen, use
[ ]/[ ] to select “Recorder, and then press [ ].
2. Use [ ]/[ ] to move the cursor to Auto Rec Start
setting, and use [ ]/[ ] to specify the time after
which recording will start or the level at which
recording will start.
(Default in bold)
Auto Rec Start
Auto Rec Start is not
used
OFF
Time until recording
starts
2 sec
5 sec
10 sec
Level at which recording
starts
Level1 (-60 dB)
Level2 (-30 dB)
Level3 (-20 dB)
3. Press [MENU] twice to return to the main screen.
4. From the main screen, press [ ] so the REC/PLAY
indicator is blinking red.
The R-07 will enter recording-standby mode.
5. Press [ ] once again.
Recording will begin automatically when the specied time has
elapsed or when the specied input level is detected.

Table of Contents

Other manuals for Roland R-07

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Roland R-07 and is the answer not in the manual?

Roland R-07 Specifications

General IconGeneral
Sample rate96 kHz
Audio quality24 bit
Frequency range20 - 40000 Hz
USB 2.0 ports quantity1
Product colorBlack
Weight and Dimensions IconWeight and Dimensions
Weight150 g
Dimensions (WxDxH)61 x 103 x 26 mm

Related product manuals