59
Settings
Example 3: Performing while listening to a click/
guide track
With these settings, all sound is output to the PHONES jacks for
monitoring.
By outputting CLICK (the click and song click track output) and USB
IN SUB (the sound that is input to the USB COMPUTER port) only from
headphones, only the player can hear the click or guide track while
they perform.
Connector Output setting Example destination
PHONES
All
CLICK and USB
IN SUB are
output only to
PHONES
Monitor headphones
MASTER OUT
Output only
SONG and USB
IN MAIN
PA (external mixer)
DIRECT OUT 1
KICK
DIRECT OUT 2
SNARE
DIRECT OUT 3
HI-HAT
DIRECT OUT 4
RIDE
DIRECT OUT 5/6
TOM 1–4
(Stereo)
DIRECT OUT 7/8
CRASH 1,
2, AUX1–4
(Stereo)
Conguring the detailed output routing
Here’s how to make the detailed settings for output routing to the
MASTER OUT jacks, DIRECT OUT jacks, and PHONES jacks.
Reference
For details on the parameters that can be edited, refer to “Data List”
(PDF).
1. In the SETUP MENU 1 screen (p. 57), press the [F1]
(OUTPUT) button.
2. Press the PAGE [DOWN] button to display page 3
(OUTPUT ROUTING).
The routing screen appears.
3. Press the [F1] (ROUTING)–[F3] (ATT) buttons to select
the item that you want to edit.
Button Explanation
[F1] (ROUTING)
button
Species how the fader, pad equalizer/
compressor, master out output and so on are
applied or routed.
Button Explanation
[F2] (LO CUT)
button
Species whether the low-frequency region is
cut from the output.
The frequency setting is the same for each
output.
[F3] (ATT) button
Species whether to apply an attenuator to the
signal output from the DIRECT OUT jacks.
When “Master Out” on the ROUTING tab is set
to “DIRECT,” this is enabled for the MASTER OUT
jacks as well.
For details on the Master Out parameters, refer
to “Data List” (PDF).
MEMO
5
To return to the default values, press the [F4] (DEFAULT) button.
5
The LO CUT and ATT settings have no eect on USB audio output.
4. Press the [KIT] button to return to the DRUM KIT screen.
Routing parameter setting examples
Parameter Explanation
Fader to Direct
When turned “OFF”
5
The panel faders have no eect on the
output from the DIRECT OUT jacks. When
the OUTPUT ROUTING Master Out setting
is “DIRECT,” the panel faders have no eect
on the output from the MASTER OUT
jacks. The panel faders are always enabled
for the PHONES jack output, regardless of
the Fader to Direct setting.
5
This lets the player adjust their monitoring
sound balance using the faders at hand,
apart from the sound balance that is
adjusted on the PA system.
PadEq/Comp to
Direct
When turned “OFF”
5
The output from the DIRECT OUT jacks
bypasses the pad equalizer and pad
compressor. The output from the MASTER
OUT jacks bypasses the pad equalizer and
pad compressor if the OUTPUT ROUTING
Master Out setting is “DIRECT.”
5
While the equalizer and compressor
for each pad are adjusted at the PA, the
performer can perform with the sound
processed by the pad equalizer and pad
compressor of each drum kit.
PadComp to
Phones
When turned “OFF”
5
The pad compressor does not apply to the
output from the PHONES jacks.
5
With settings such as shown in output
destination setting example 2 (p. 58),
you can hear the sound with full dynamics
in your monitor headphones as you
perform, yet use the pad compressor to
reduce the dynamics for the drum monitor
and the PA.
To Next Page
Loading...
