Roland VR-50HD MK II - Menu List; Audio Settings Overview; Audio Channels 1-4 Settings

37
Menu List
Audio
Audio Ch. 1–4 Screen
(Press a channel 1–4 [SELECT] button, or [MENU] button
0
Audio <1>–<4>)
These settings adjust the input audio of channels 1–4.
Menu item Value (bold text: default value) Explanation
+48V OFF, ON Turns the phantom power on/o. If this is “ON,” phantom power is supplied via the AUDIO IN jacks (XLR).
Solo OFF, ON Turns the solo function on/o. Only the audio for which this is “ON” is heard in the headphones.
Mute OFF, ON Turns the mute function on/o. If this is “ON,” the audio is temporarily silenced.
A.Gain 0.0– +68.0dB
Adjusts the input gain (sensitivity) in the analog domain.
* This can also be adjusted by the [GAIN] knob.
D.Gain -42.0–0.0– +42.0dB Adjusts the input gain (sensitivity) in the digital domain (after conversion from analog to digital).
Level -Inf–10.0dB
Adjusts the input volume.
* This can also be adjusted by the channel fader.
HPF OFF, ON
Turns the high-pass lter on/o.
Eect Cuts o unneeded low-band audio. The cuto frequency is 80 Hz.
Delay 0.0–500.0ms Adjusts the delay time of the audio. Delays the output of the audio by the specied time.
Pan
Left, L49–L01, Center
R01–R49, Right
Adjusts the stereo position (pan).
AUX 1 Send -Inf–10.0dB Adjusts the amount of audio sent to the AUX 1 bus.
Send Point
Species the position from which the audio sent to the AUX 1 bus is taken.
Pre Send the audio before it is adjusted by the fader (pre-fader).
Post Send the audio after it passes through the fader (post-fader).
Unity — Sets “AUX 1 Send” to unity (0.0 dB).
AUX 2 Send -Inf– +10.0dB Adjusts the amount of audio sent to the AUX 2 bus.
Send Point
Species the position from which the audio sent to the AUX 2 bus is taken.
Pre Send the audio before it is adjusted by the fader (pre-fader).
Post Send the audio after it passes through the fader (post-fader).
Unity — Sets “AUX 2 Send” to unity (0.0 dB).
Reverb Send 0–127 Adjusts the amount of audio sent to reverb.
Gate
Gate OFF, ON
Turns the gate on/o.
Eect
Eliminates audio that is lower than the specied threshold level. This is eective when the
noise that you want to remove is separate from the audio that you want to keep, and can be
used to remove hiss or other noise that is heard during periods of silence.
Threshold -80– -48–0dB
Species the level used as the threshold for removing audio.
Release 30–500–5000ms
Species the length of time until the audio is fully attenuated after audio falls below the threshold.
Compressor
Compressor OFF, ON
Turns the compressor on/o.
Eect
Audio that exceeds the specied threshold level is compressed. This reduces the dierence
between the maximum volume and minimum volume, making the audio more comfortable
for listening.
Threshold -50– -8–0dB
Species the level used as the threshold at which the compressor is applied. Compression is applied to
audio that exceeds the threshold.
Ratio
1.00 : 1, 1.12 : 1, 1.25 : 1
1.40 : 1, 1.60 : 1, 1.80 : 1
2.00 : 1, 2.50 : 1, 3.20 : 1
4.00 : 1, 5.60 : 1, 8.00 : 1
16.0 : 1, INF : 1
Species the degree of compression applied to the audio. The state in which no compression is applied
is dened as “1.”
Attack 0–30–100ms Adjusts the time from when audio exceeding the threshold is input until when compression begins.
Release 30–250–5000ms Adjusts the length of time until compression ends after audio falls below the threshold.
Makeup -40–0–40dB Adjusts the output volume level after applying the compressor.