58
LAN/RS-232C Command Reference
List of Commands
* When sending a sequence of commands to this unit from a controller, after each one, be sure to verify that an “ACK” response is returned before
sending the next command.
Item
Sent
command
Response
command
Parameter
Select video input stxPGM:a; ack a: 0 (INPUT 1), 1 (INPUT 2), 2 (INPUT 3), 3 (INPUT 4), 4 (STILL)
Select transition eect stxTRS:a; ack a: 0 (CUT), 1 (MIX), 2 (WIPE)
Set video transition time stxTIM:a; ack a: 0–40 (0.0–4.0 sec)
Set the [PinP] button on/o stxPIP:a; ack a: 0 (OFF), 1 (ON)
Set the [PinP/KEY] button on/o stxPKY:a; ack a: 0 (OFF), 1 (ON)
Set the [STILL KEY] button on/o stxSKY:a; ack a: 0 (OFF), 1 (ON)
Set the [OUTPUT FADE] button on/o stxFDE:a; ack a: 0 (OFF), 1 (ON)
Set the [FREEZE/USER LOGO] button on/o stxULF:a; ack a: 0 (OFF), 1 (ON)
Adjust volume of audio channel 1 stxLM1:a; ack a: 0 (-Inf dB)–127 (+10 dB)
Adjust volume of audio channel 2 stxLM2:a; ack a: 0 (-Inf dB)–127 (+10 dB)
Adjust volume of audio channel 3 stxLM3:a; ack a: 0 (-Inf dB)–127 (+10 dB)
Adjust volume of audio channel 4 stxLM4:a; ack a: 0 (-Inf dB)–127 (+10 dB)
Adjust volume of audio channels 5/6 stxLS1:a; ack a: 0 (-Inf dB)–127 (+10 dB)
Adjust volume of audio channels 7/8 stxLS2:a; ack a: 0 (-Inf dB)–127 (+10 dB)
Adjust volume of audio channels 9/10 stxLS3:a; ack a: 0 (-Inf dB)–127 (+10 dB)
Adjust volume of audio channels 11/12 stxLS4:a; ack a: 0 (-Inf dB)–127 (+10 dB)
Adjust volume of main output stxLMN:a; ack a: 0 (-Inf dB)–127 (+10 dB)
Recall memory stxMEM:a; ack a: 0 (Memory 1)–7 (Memory 8)
Select video for AUX bus stxAUX:a; ack a: 0 (INPUT 1), 1 (INPUT 2), 2 (INPUT 3), 3 (INPUT 4), 4 (STILL), 4 (PinP)
5 (PinP/KEY), 6 (PGM)
Select source video for video input stxVIS:a,b; ack a: 0 (INPUT 1), 1 (INPUT 2), 2 (INPUT 3)
, 3 (INPUT 4), 4 (STILL)
b:0 (SDI), 1 (HDMI), 2 (COMPOSITE), 3 (RGB/COMPONENT)
* When a=2 (INPUT 3) or 3 (INPUT 4), you can select 0 (SDI) and 1 (HDMI) only.
Select still image of the [STILL] button stxSTS:a; ack a: 0 (STILL 1), 1 (STILL 2), 2 (STILL 3), 3 (STILL 4)
Select source video for PinP stxPIS:a; ack a: 0 (SDI 1), 1 (SDI 2), 2 (SDI 3), 3 (SDI 4), 4 (HDMI 1), 5 (HDMI 2), 6 (HDMI 3)
7 (HDM 4), 8 (COMPOSITE 1), 9 (COMPOSITE 2), 10 (RGB/COMPONENT 1)
11 (RGB/COMPONENT 2)
Select source video for PinP/KEY stxPKS:a; ack a: 0 (SDI 1), 1 (SDI 2), 2 (SDI 3), 3 (SDI 4), 4 (HDMI 1), 5 (HDMI 2), 6 (HDMI 3)
7 (HDM 4), 8 (COMPOSITE 1), 9 (COMPOSITE 2), 10 (RGB/COMPONENT 1)
11 (RGB/COMPONENT 2)
Select source image for STILL KEY stxSKS:a; ack a: 0 (STILL 1), 1 (STILL 2), 2 (STILL 3), 3 (STILL 4)
Recall preset memory on remote camera stxCML:a,b; ack a: 0 (CAMERA 1)–5 (CAMERA 6)
b:0 (Memory 1)–7 (Memory 8)
Acquire status of the VIDEO INPUT SELECT
buttons
stxQPG; stxQPG:a; a: 0 (INPUT 1), 1 (INPUT 2), 2 (INPUT 3), 3 (INPUT 4), 4 (STILL)
Enable spontaneously sending status of the
VIDEO INPUT SELECT buttons
stxCPG:a; ack a: 0 (OFF), 1 (ON)
Reset USB connection stxUVR; ack
Acquire status of USB streaming stxUVQ; stxUVS:a,b; a: 0 (unconnected), 1 (USB 2.0), 2 (USB 3.0)
b:Number of dropped frames
Acquire status of the unit stxACS; ack
Version information stxVER; stxVER:a,b; a: VR-50HDMK2 Product name
b:Version number The version info is ASCII text strings.
To Next Page
Loading...
