Sanyo PLV-80 - Page 40

-40-
Electrical Adjustments
Group
No. Item Function Range Initial Value
10 GAIN target White Level adj. Target Value 0 - 255 235
11 GAIN torelance White Level Adj. Tolerance Range 1 - 255 1
12 Auto Status
Result of Auto Calibration (Maintain Last Adj.)
0: End correctly
1: On Calibration
9: End with Error
0 / 1 / 9 0 (Read only)
13 AutoWait Wait value for each Settings 1 ~ 20 1
14 CHECK -Tolelance OFFSET Tolerance 1 ~ 255 1
681 AutoPC Adjsut
0 AutoPCAdjustEnable 0: AutoPCAdjust Enable 1:AutoPCAdjust Prohiit Normally 0 ~ 1 0
1 Frequency Step Frequency Step in TotalDot Search 0-3 1
2 Frequency Threshold
Confirm TotalDot
0 [] <--- -----> 10 [No]
0 ~ 10 5
3 Fine Phase
Executes Phase after Total Dot Adj.
0: Executes FinePhase1:Not Execute
0 ~ 1 0
4 BLKDET Detection Area of Black Level 0 ~ 3 1
5 PHASEMSK
Phase Detection Filter 0:Effect All Bit 1: Disable lower 1 bit
2:Disable lower 2 bit 3:Disable lower 3 bit
0 ~ 3 0
690 CUSTOM(Aspect)
0 Connect Indivisual/Link Edition (0: Indivisual, 1: Link) 0 - 1 0
1 Horizontal Scaler H-Scaler Edition 0 - 200 100
2 Horizontal Position H-Position Correction 0 - 200 100
3 RESET/STORE Reset of H-Aspect/Save (0: reset, 1: Save) 0 - 1 0
4 Vertical Scaler V-Scaler Edition 0 - 200 100
5 Vertical Position V-Position Correction 0 - 200 100
6 RESET/STORE Reset of V-Aspect/Save (0: reset, 1: Save) 0 - 1 0
7 Screen Select Screen Mode Selection (0:FULL 1:NORMAL) 0 - 1 0
8 CUSTOM ON/OFF Custom (0: Disable, 1: Enable) 0 - 1 0
700 General
0 IP Mode
Setting at IP OFF
0:Not used for IP Block
1:IP OFF with IP Block
0 - 1 1
1 3:2 PullDown Mode
bit0 : Global Motion
bit1 : Video Motion
1 - 3 1
2 Detect Film Mode Enable
0 : 2:3pull down & 2:2pull down
1 : 2:3pull down
2 : 2:2pull down
0 - 2 0
3 Force IP Mode
0 : IP Process Disable
1 : Force Normal IP Mode
2: Force Film Mode
0 - 2 0 * Effective only for PSF signal
701 Deinterlacer setting Effective only for Progressive ON / Film
0 Motion Adaptive Weight Value <KDEINT> 0 - 255 25
1 Angle Interpolation Level 0 : Conservative <====> 4 : Aggressive 0 - 4 2
2 CUE LOW Pass Filter Enable <CUELPFEN> 0 - 1 0
702 Deinterlacer setting Effective only for Progressive ON - L2
0 Motion Adaptive Weight Value <KDEINT> 0 - 255 0x19
1 Angle Interpolation Level 0 : Conservative <====> 4 : Aggressive 0 - 4 0x02
711 Noise Reduction (Time) Effective only for N.R L1
0 Noise Pixel Range <NSRANGEY> / <NSRANGEUV> 0 - 2 1
1 Noise Region 0 <NSREGIONY0> / <NSREGIONUV0> 0 - 1023 12
2 Noise Region 1 <NSREGIONY1> / <NSREGIONUV1> 0 - 1023 24
3 Noise Region 2 <NSREGIONY2> / <NSREGIONUV2> 0 - 1023 40
4 Noise Gain Level <NSFILTERY**> / <NSFILTERUV**> 0 - 255 50
713 Noise Reduction (Time) Effective only for N.R L2
0 Noise Pixel Range <NSRANGEY> / <NSRANGEUV> 0 - 2 1
1 Noise Region 0 <NSREGIONY0> / <NSREGIONUV0> 0 - 1023 12
2 Noise Region 1 <NSREGIONY1> / <NSREGIONUV1> 0 - 1023 24
3 Noise Region 2 <NSREGIONY2> / <NSREGIONUV2> 0 - 1023 40
4 Noise Gain Level <NSFILTERY**> / <NSFILTERUV**> 0 - 255 100
715 Noise Reduction (Time) Effective only for N.R OFF
0 Noise Pixel Range <NSRANGEY> / <NSRANGEUV> 0 - 2 1
1 Noise Region 0 <NSREGIONY0> / <NSREGIONUV0> 0 - 1023 12
2 Noise Region 1 <NSREGIONY1> / <NSREGIONUV1> 0 - 1023 24