-63-
Pin Function Name Function Pol. Action
193 (Not used) SIOF Send Data/Output Port for SCI - (Open)
194 (Not used) SIOF Clock In/IO Port for SCI - (Pull-up)
195 SH_EX_UART Send Data2 [External] O 19200bps or 9600bps
196 (Not used) SIOF Clock/IO Port for SCI - (Pull-up)
197 (Not used) SIOF Frame Sync/IO Port for SCI - (Pull-up)
198 LB_SH_UART Dimmer Control I Lamp Error Detection
199 (Not used) SIOF Receive Data/IO Port for SCI - (Pull-up)
200 GND Power (0V) - -
201 EX_SH_UART Receive Data2 [External] I 19200bps or 9600bps
202 1.9V Power (1.9V) - -
203 (Not used) I (Pull-up)
204 FPGA_NCONFIG Start configuration O L -> H start configuration
205 BOX_RQST For PJ-Net O Fixed L
206 NET_SW Switch On/Off for PJ-Net Power O L:On, H: Off
207 GND Power for Inout/Output(0V) - -
208 FPGA_CLB Initialize for circuit O H after configuration
209 3.3V Power for Inout/Output(3.3V) - -
210 SYS SW_CPU Bus Switch O
211 IC_RESET_CPU Power Control peripheral ICs O
212 LAMP_SWIN Lamp Drive O H: On, L: Off
213 FAN_DRIVE_CPU Fan Drive O H: On, L: Off
214 SH_SDA_3V IIC Bus IO L: Active
215 SH_SCL_3V IIC Bus IO L: Active
216 SH_SDA_S3V IIC Bus IO L: Active
217 SH_SCL_S3V IIC Bus IO L: Active
218 PW_SH_0 PW-SH Input SIgnal I
219 UCLK USB Clock [48MHz] I -
220 RESETP Power On Reset Request I -
221 (Not used) Hardware Reset Request - (Pull-up)
222 MD3 Bus Width Setting for Area0 I H Fixed
223 MD4 Bus Width Setting for Area0 I H Fixed
224 3.3V Test(3.3V Fixed) I -
225 3.3V USB Analog Power(3.3V) - -
226 (USB1P)[Func] USB1 Data I/O(+) I/O
227 (USB1M)[Func] USB1 Data I/O(-) I/O
228 GND USB Analog Power (0V) - -
229 (USB2P)[Host] USB2 Data I/O(+) I/O
230 (USB2M)[Host] USB2 Data I/O(-) I/O
231 3.3V USB Analog Power(3.3V) - -
232 GND Analog Power (0V) - -
233 PRESS_SENS Input for Pressure Sensor AI (pull-down)
234 (Not used)
235 KEY1 KEY AD Converter Input AI
236 KEY2 KEY AD Converter Input AI
237 3.3V Analog Power(3.3V) - -
238 KEY3 KEY AD Converter Input AI
239 OPT1 KEY AD Converter Input * Option Inut AI
240 GND Analog Power (0V) - -
Parallel I/O Expander(TE7780) (IC4801)
1 SH_PJ_UART1 For PJ-Net Command (SH: TXD) O
2 GND - -
3 PJ_SH_UART1 For PJ-Net Command (SH: RXD) I
4 (Not used) O
5 (Not used) I
6 (Not used) O
7 (Not used) I
8 Open
9 (Not used) O
10 LENS_DOWN_EX Lens Shift Down O L: Active, H: Stop
11 LENS_UP_EX Lens Shift Up O L: Active, H: Stop
12 GND - -
13 SH_PW_0 Output Signal SH to PW O
14 PWR_LED_EX Power LED Drive O L: Light On Brightly, H: Light On Darkly
15 READY_LED_EX Ready LED Drive O L: On, H: Off
Control Port Functions
To Next Page
Loading...
