PN 9001079
Rev. B
Index-2
SATO CL608e/CL612e Service Manual
Index
I
IEEE 1284 Parallel Interface 3-4, 8-2
Indexing Notch 6-5
Interface Board 4-3
Interface Card 6-3
Interface Option 10-31
Interface Slot 1-3
Interface Specifications 3-1
Interface Types 3-1
Intermittent Problems 8-6
K
KB Board 1-7
L
Label Cutter Kit Installation 9-2
Label Dispenser Installation 9-6
Label Gap Adjustment 4-10
Label Out Sensor 1-9
Label Sensor Selection 2-5
Label Supply Guide 1-4
Label Tear Off Plate 1-4
Lan Ethernet Interface Installation Problems 8-5
Lan Ethernet Interface 8-5
LCD Board 1-7
LCD Display Adjustment 4-15
LCD Display 1-5
LCD Panel, Counters Mode 2-32
LCD Panel, Download User Defined Protocol 2-37
LCD Panel, Firmware Download Mode 2-39
LCD Panel, Normal Mode 2-9
LCD Panel, Card Mode 2-17
LCD Panel Configuration 2-8
LCD Panel, Clear Non-Standard Protocol 2-37
LCD Panel, Maintenance Mode 2-35
LCD Panel, Test Print Mode 2-33
LCD Screen 1-5
Line Key 1-5
Low level adjustment 4-11
M
Main PC Board 6-8
Main PCB Assembly 10-30
Main PCB Board 4-3, 9-17
Main PCB Memory Frame 6-5, 9-19
Mechanical Adjustments 5-1
Media Hold Down Cover 6-30
Media Hold Down Unit 6-35
Media Hold Down 1-9
Media Knob 1-4
Memory Card Slot 1-3
Memory Module PCB 6-5
Multi Job Buffer 3-3
N
NetWare Troubleshooting 8-7
Notch/Gap and Eye-Mark Sensors 6-34
Notch/Gap Sensor 1-9, 6-30, 6-35
Notch/Gap Sensor Adjustment 5-13
O
Offset Label Stop Position Adjustment 4-12
Online LED 1-5
Operation Panel/Displays 1-5
Optional Accessories 1-10, 9-1
P
Paper End Switch 6-30, 6-33
Parity Selection 2-2
PCB Harness 6-28
PCMCIA Memory Expansion Installation 9-15
PCMCIA Memory Expansion Slot 1-3
PCMCIA Memory Option 10-43
Physical Characteristics 1-2
Pin Assignments, Accessory (EXT) Connector 3-11
Pin Assignments, IEEE1284 Cable End 3-5
Pin Assignments, RS232C Printer End 3-6
Pitch Offset Adjustment 2-10
Platen Roller 1-4
Platen 1-7, 6-17
Plug In Interface Card 1-8
Potentiometer Assignments & Adjustments 4-6
Potentiometers 1-6
Power LED 1-5
Power Supply 1-8, 4-1, 4-3, 6-9
Power Switch 1-3
Print Darkness Adjustment 4-16
Print Darkness Setting 2-9
Print Head Assembly 1-4, 10-18
Print Head Balance Adjustment 5-7
Print Head Position Adjustment 5-5
Print Head 1-7, 6-16
Print Offset 2-14
Print Position Adjustment 4-8
Print Quality Problems 8-11
Print Speed Adjustment 2-10
Printer Features 1-3
Printer Set up 2-3
Priority Setting LCD Command 2-31
Protocol Code Selection 2-4
Protocol Selection 2-2
R
Ramp Frame 6-32
Ramp Plate 6-32
Ready/Busy Flow Control 3-8
To Next Page
Loading...
