Seatex DPS 132 - Page 72

Seatex DPS 132 Installation Manual, rev. 0 Appendix D - DPS setup file
60
! TOPNAV = DGPS and DVAR from Thales receivers.
! NONE = No input expected (DPS 102 only)
! DCLNKx SHORT RANGE 1: Treat link as a short range link (e.g. IALA)
! 0: Normal operation
! DCLNKx ROLL BYTES options: 0: lsb first 1: msb first (RTCM standard)
! DCLNKx 6 OF 8 BITS BYTE : 0: 8 of 8 1: 6 of 8
! DCLNKx DEBUG 1: debug printout logging enabled 0: disabled
! DCLNKx ENABLE_GLONASS_CORR DPS200 only: 1: enable decoding of GLONASS corrections.
!
! Value of ENABLE_GLONASS_CORR is ignored on DPS 100 and DPS 116 systems
!
! Value IONOSPHERE COMPENSATED defines if the corrections are compensated for
! Ionosphere difference between reference station and mobile based on dual
! frequency measurements (ex.g. Fugro's Starfix+ system). Normal here is uncompensated.
!
! Value REF STATION OFFSET reads an offset in x,y,z (north/south, east/west, hight) for the
! reference station position. Some links can deliver differential corrections from reference
! stations measured in a different coordinate system (not WGS84). This offset will compensate
! for such an error.
!
!
! IMPORTANT NOTE: LINK 1 IS FOR IALA BEACON ONLY !!!
!
[DiffCorrLinks]
DIFFCORR_LINK_1 com3 4800 n 8 1 nh
DCLNK1 NAME IALA
DCLNK1 TYPE RTCM
DCLNK1 SHORT RANGE 1
DCLNK1 ROLL BYTES 1
DCLNK1 6 OF 8 BITS BYTE 1
DCLNK1 DEBUG 0
DCLNK1 ENABLE_GLONASS_CORR 0
DCLNK1 IONOSPHERE COMPENSATED 0
DCLNK1 REF STATION OFFSET 0.0 0.0 0.0
DIFFCORR_LINK_2 com5 57600 n 8 1 nh
DCLNK2 NAME LINK 2
!DCLNK2 TYPE SCF
DCLNK2 TYPE RTCM
DCLNK2 SHORT RANGE 0
DCLNK2 ROLL BYTES 1
DCLNK2 6 OF 8 BITS BYTE 1
DCLNK2 ENABLE_GLONASS_CORR 1
DCLNK2 IONOSPHERE COMPENSATED 0
DCLNK2 REF STATION OFFSET 0.0 0.0 0.0
DCLNK2 SHOW_CONSOLE 0
DIFFCORR_LINK_3 com6 57600 n 8 1 nh
DCLNK3 NAME LINK 3
!DCLNK3 TYPE SCF
DCLNK3 TYPE RTCM
DCLNK3 SHORT RANGE 0
DCLNK3 ROLL BYTES 1
DCLNK3 6 OF 8 BITS BYTE 1
DCLNK3 ENABLE_GLONASS_CORR 1
DCLNK3 IONOSPHERE COMPENSATED 0
DCLNK3 REF STATION OFFSET 0.0 0.0 0.0
DCLNK3 SHOW_CONSOLE 0
!--------------------- GYRO INTERFACE AND DECODING ----------------------------*
! Stuff for GYRO interface & decoding
! Comm parameters: nh:no handshake, sh:software handshake, hh:hardware handshake
! GYROIO_x TYPE options:
FSP ref.: A11211400XRBRA0