Seca 777 - User Manual

Questions and Answers

C
Clarence FletcherAug 16, 2025
What to do if my Seca Scales display 'bAtt'?
- D
  dorseysheriAug 16, 2025
  If 'bAtt' is displayed on your Seca Scales, this means the batteries have discharged. You should change the batteries to continue using the scales.
R
Robert PorterAug 19, 2025
What to do if my Seca Scales display the battery symbol?
- C
  christopher03Sep 12, 2025
  If your Seca Scales are displaying the battery symbol, it means the battery voltage is dropping. Replace the batteries to resolve this issue.
L
Lori RamseyAug 22, 2025
How to fix flashing weight display on Seca 777?
- A
  Adam CarpenterAug 22, 2025
  A flashing weight display on your Seca Scales indicates that a consistent weight value hasn't been detected yet. This might be because one of the following functions is active: Hold, Autohold, or Tare. Wait until the measuring station detects a consistent weight value and the display stops flashing. Alternatively, remove the load, wait for '0.0' to appear, and then weigh again.
J
Justin KingAug 25, 2025
What to do if my Seca Scales display 'Er:[No.]:12'?
- C
  Curtis JordanAug 26, 2025
  The error message 'Er:[No.]:12' on your Seca Scales indicates that the device was switched on with too high a load. To fix this, take the load off the measuring station and then switch the scales off and back on again.
J
Jason CrawfordAug 28, 2025
What does it mean when my Seca 777 Scales display 'Er:[No.]:11'?
- C
  Christina StevensAug 28, 2025
  The message 'Er:[No.]:11' on your Seca Scales means that the device has too high a load or too much weight concentrated in one corner. Try removing some of the load or distributing the weight more evenly. Then, switch the scales off and back on again. If the problem continues, contact Seca Service.
T
Thomas PetersonAug 31, 2025
Why does my Seca 777 Scales not display weight when loaded?
- D
  Dana LeeAug 31, 2025
  If your Seca Scales aren't displaying a weight with a load on the platform, the device might not have power. Try the following: - Switch on the measuring station. - If using batteries: Insert batteries. - If using a power supply: Connect the plug-in power supply unit.
M
Melissa TorresSep 3, 2025
What does 'Er:[No.]:32' mean on my Seca 777 and how to fix it?
- C
  Charles EvansSep 3, 2025
  The error message 'Er:[No.]:32' on your Seca Scales indicates an internal communication error. Try switching the measuring station off and then back on again. If the problem continues, contact Seca Service.
M
Michael MoyerSep 6, 2025
What does 'Er:[No.]:16' mean on my Seca Scales?
- M
  Mr. Anthony ChambersSep 6, 2025
  The error message 'Er:[No.]:16' on your Seca Scales means that the device was caused to oscillate, and the zero point could not be determined. Try switching the measuring station off and then back on again.
A
Adam NovakSep 9, 2025
Why does my Seca Scales display '- - - - -' before weighing?
- T
  Tony PattonSep 9, 2025
  If your Seca Scales display '- - - - -' before weighing, it means a load was already on the device when it was switched on. Remove the load from the measuring station, switch the scales off, and then switch them back on.
M
Michael RamirezSep 12, 2025
What to do if a display segment is defective on my Seca Scales?
- N
  nchandlerSep 12, 2025
  If one display segment on your Seca Scales is continuously on or not displayed at all, it indicates that the display is defective. Inform Seca Service about this issue.