Seg WI Series Reference Manual

150 pages

To Next Page

To Previous Page

TCM . Alarm [Operation / Status Display / Alarms]

[Operation / Status Display / TCM]

Signal: Alarm

114 WIC1 WIC1-2.0-EN-REF

9 Protection Parameter

9.22.1.4 TCM: Signals (Output States)

Table of Contents3
About this Reference Manual8
Hardware11
Device Configuration11
Diggimec13
Diggimec: Device Planning Parameters13
Diggimec: Settings13
Security16
Field Settings17
CT - Current Transformer17
CT: Settings17
CT: Direct Controls20
CT: Values23
System26
Time26
Sys - System27
Sys: Direct Controls27
Sys: Values27
Measured Values29
Statistics30
Peak Current Ptr - Statistic of the Current Measuring Values31
Peak Current Ptr: Settings31
Peak Current Ptr: Direct Controls31
Peak Current Ptr: Values31
Life Load - Load Current Histogram32
Life Load: Device Planning Parameters32
Life Load: Settings32
Life Load: Direct Controls32
Life Load: Input States33
Life Load: Signals (Output States)33
Life Load: Values33
Communication34
Modbus34
Modbus: Device Planning Parameters34
Modbus: Settings34
Modbus: Direct Controls35
Modbus: Values35
Protection Parameter36
Prot: Device Planning Parameters36
Prot: Settings36
Prot: Direct Controls43
Prot: Input States44
Prot: Signals (Output States)44
Prot: Values47
IH2 - Module Inrush48
IH2: Device Planning Parameters48
IH2: Settings48
IH2: Signals (Output States)49
I> - Phase Overcurrent Stage50
I>: Device Planning Parameters50
I>: Settings50
I>: Input States54
I>: Signals (Output States)55
I>> - Phase Overcurrent Stage57
I>>: Settings57
I>>: Input States61
I>>: Signals (Output States)61
IG> - Ground (Earth) Current Protection Stage71
IG>: Device Planning Parameters71
IG>: Settings71
IG>: Input States76
IG>: Signals (Output States)76
IG>> - Ground (Earth) Current Protection Stage78
IG>>: Device Planning Parameters78
IG>>: Settings78
IG>>: Input States83
IG>>: Signals (Output States)83
I2/I1> - Unbalanced Load Protection85
I2/I1>: Device Planning Parameters85
I2/I1>: Settings85
I2/I1>: Input States86
I2/I1>: Signals (Output States)86
I2> - Negative-Sequence Current Protection88
I2>: Device Planning Parameters88
I2>: Settings88
I2>: Input States91
I2>: Signals (Output States)91
Thr - Thermal Replica Module93
Thr: Device Planning Parameters93
Thr: Settings93
Thr: Direct Controls94
Thr: Input States94
Thr: Signals (Output States)94
Thr: Values95
Ipeak> - Peak-Value Overcurrent96
Ipeak>: Device Planning Parameters96
Ipeak>: Settings96
Ipeak>: Input States97
Ipeak>: Signals (Output States)97
SOTF - Switch Onto Fault - Module99
SOTF: Device Planning Parameters99
SOTF: Settings99
SOTF: Input States100
SOTF: Signals (Output States)100
Exp[1] - External Protection - Module102
Exp[1]: Device Planning Parameters102
Exp[1]: Settings102
Exp[1]: Input States104
Exp[1]: Signals (Output States)104
Exp[2] - External Protection - Module105
Exp[2]: Device Planning Parameters105
Exp[2]: Settings105
Exp[2]: Input States107
Exp[2]: Signals (Output States)107
CBF - Circuit Breaker Failure Protection Module109
CBF: Device Planning Parameters109
CBF: Settings109
CBF: Input States109
CBF: Signals (Output States)109
CLPU - Cold Load Pickup Module111
CLPU: Device Planning Parameters111
CLPU: Settings111
CLPU: Input States112
CLPU: Signals (Output States)112
Supervision113
TCM - Trip Circuit Monitoring113
Bkrwear - Breaker Wear115
SBM - Station Battery Monitoring118
Records119
Fault Recorder119
Self-Supervision120
Service121
Selection Lists122
Index147

Other manuals for Seg WI Series

Manual337 pages

Maintenance7 pages

Questions and Answers:

Need help?

Do you have a question about the Seg WI Series and is the answer not in the manual?

Seg WI Series Specifications

General

Brand	Seg
Model	WI Series
Category	Relays
Language	English

Related product manuals

Seg WI Series Reference Manual

Table of Contents

Other manuals for Seg WI Series

Questions and Answers:

Seg WI Series Specifications

Related product manuals