Seitron CHEMIST 600 User Manual (English)

Questions and Answers:

C
Chad BakerAug 15, 2025
What to do if sample pump of Seitron Measuring Instruments isn't working properly?
- B
  Brian MurilloAug 15, 2025
  If the sample pump of your Seitron Measuring Instruments sounds slow, stops, or doesn't start, check for obstructions in the sample flow by cleaning the water filter and ensuring the hose connected to the probe isn't crushed. Also, verify the particulate filter is clean and that the pump's electrical connector is properly connected to the printed circuit board. If these steps don't resolve the issue, the pump may be faulty and need replacement. Finally, ensure the pump hasn't been disabled by a key combination; if so, restart the instrument.
K
kathleen71Aug 18, 2025
Why are the readings on my Seitron CHEMIST 600 Measuring Instruments inaccurate?
- M
  Melanie MoraAug 18, 2025
  If the values displayed on the analysis screen of your Seitron Measuring Instruments seem unreliable, start by checking that the sensors are correctly installed via the sensor diagnostics menu. Inspect all joints and the hose for leaks in the sample probe connection. If the issue persists, the pump might be faulty and require replacement. In some cases, the instrument itself may be faulty and need to be sent to a service center for repair.
S
Shannon DavilaAug 21, 2025
What to do if battery symbol is empty on Seitron CHEMIST 600?
- N
  nwilcoxAug 21, 2025
  If the battery symbol is empty on the inside on your Seitron Measuring Instruments, it means the batteries are low. Connect the battery charger to recharge them.
B
Benjamin RogersAug 26, 2025
What does flue gas temperature error mean on Seitron Measuring Instruments?
- E
  edwardkleinAug 26, 2025
  If the analysis screen of your Seitron Measuring Instruments shows a flue gas temperature (Tf) error, first, ensure the thermocouple is properly connected to the analyzer. If the error persists, the thermocouple may have been exposed to temperatures beyond its operating range or is faulty, requiring the probe to be sent to a service center.
M
mchenAug 28, 2025
What to do if 'sensor error' is reported during tightness test of Seitron CHEMIST 600 Measuring Instruments?
- J
  James BrownAug 28, 2025
  If your Seitron Measuring Instruments reports a 'sensor error' during the tightness test, verify that the hose is correctly connected to the positive pressure input.
R
Ronald StewartSep 1, 2025
Why do I get a sensor error after auto-calibration on Seitron CHEMIST 600 Measuring Instruments?
- K
  kerrrodneySep 1, 2025
  If, after auto-calibration, the sensor diagnostics screen of your Seitron Measuring Instruments displays an error for one or more cells, it could be due to auto-calibration occurring while flue gas was being sampled. Also, check the O2 sensor's connections and condition, referring to sections 10.6.2, 10.7.1, and 15.0. The sensor may also need adequate adjustment time, or the instrument may have been left with a low battery for too long.
V
Valerie NelsonSep 4, 2025
Why is the display backlight not working on my Seitron Measuring Instruments?
- A
  Ana KerrSep 4, 2025
  If the rear lighting of the display on your Seitron Measuring Instruments isn't working, the backlighting LEDs may be faulty. Contact a service center to replace the display.
T
Tammy ChenSep 7, 2025
What does pressure sensor error mean on Seitron CHEMIST 600?
- L
  Laura ClarkSep 7, 2025
  If a pressure sensor error appears on the pressure/draft screen of your Seitron Measuring Instruments, it indicates a calibration problem. The instrument needs to be sent to a service center.
B
Brian WilliamsSep 12, 2025
Why is the battery life so short on my Seitron CHEMIST 600 Measuring Instruments?
- B
  Billy KingSep 12, 2025
  If the battery operating time of your Seitron Measuring Instruments is less than 9 hours, it could be due to the battery capacity being limited by low temperatures. Storing the instrument at higher temperatures is recommended to extend battery life. Alternatively, the battery pack may be old and need replacement if its life has become unacceptable.