Selec ATSEL FD300 User Manual

27
26
Voltage
decline time
of V/F
separation
0.0s 〜 1000.0s
Note:Indicates the time from
0V changes to the rated
voltage of the motor
0.0s
V/F Separate
shutdown
mode
selection
0
50~200% 150%
Over-current
suppression
0:Invalid
1: Valid
1
Over current
stall gain
0~100 20
Double
speed overrun
speed action
current
compensation
coefficient
50~200% 50%
Overvoltage
stall
operating
voltage
200.0V~2000.0V
0:Invalid
1:Valid
1
Overvoltage
stall
suppression
frequency
gain
0~100 30
Overvoltage
stall
suppression
voltage gain
Overvoltage
stall
maximum
rising
frequency
limit
0~50Hz
5Hz
Slip
compensation
time constant
0.1~10.0s 0.5
Function
Code
Parameter
Name
Setting Range
Default
Prope-
rty
Modbus
Address
P3-16
○
P3-17
○
0 : frequency / voltage is
independently reduced to 0
1 : After the voltage is reduced
to 0, the frequency is reduced
again.
Overcurrent
stall
operating
current
P3-18
●
P3-19
●
P3-20
○
P3-21
●
P3-22
●
Model
dependent
220V:380V
380V:760V
480V:850V
Overvoltage
stall enable
P3-23
●
P3-24
●
0~100 30 P3-25
●
P3-26
●
P3-27
Fun-
ction
Code
Parameter
Name
Setting range
Default
Prope-
rty
Modbus
Address
○
P4: Multi functional inputs parameters
P4-00
Fun-
ction
Code
Parameter
Name
Setting range
Default
Prope-
rty
Modbus
Address
X1 Terminal
function
selection
1
4
9
●
P4-01
X2 Terminal
function
selection
●
P4-02
X3 Terminal
function
selection
●
12 P4-03
X4 Terminal
function
selection
●
User Manual
Chapter 5
User Manual
Chapter 5
P3-34
Water supply
mode
selection
0: Turn off water supply mode
1: Turn on the water supply mode
0
P3-35
Remote
transmission
of pressure
gauge range
0.00〜5.00MPa 1.00MPa
P3-36
Demand target
pressure
0.00~P3-39 0.5MPa
P3-37
Dormancy
frequency
0.00 Hz~P0-10 25.00Hz
P3-38
Sleep latency
0.0~3600.0s 0.0s
P3-39
Wake up the
pressure
0.0~100.0% 80%
P3-40
Wake up time
delay
0.0~3600.0s 0.0s
●
○
0 : No function
1 : Forward RUN (FWD)
2 : Reverse RUN (REV)
3 : Three-line control
4 : Forward JOG (FJOG)
5 : Reverse JOG (RJOG)
6 : Terminal UP
7 : Terminal DOWN
8 : Coast to stop
9 : Fault reset (RESET)
10 : RUN pause
11 : Normally open (NO) input of
external fault
12: Multi-speed 1
13: Multi-speed 2
14: Multi-speed 3
15: Multi-speed 4
16 : Acceleration/deceleration
time selection 1
○
○
○
○
○
62225
62226
62227
62228
62229
62230
62231
62232
62233
62234
62235
62236
62243
62244
62245
62246
62247
62248
62249
62465
62466
62467
62468

Selec ATSEL FD300 Specifications

General

Brand	Selec
Model	ATSEL FD300
Category	DC Drives
Language	English