Sencore ReZolver LC103 User Manual

16
To enter component tolerance:
1. Enter a 1, 2, or 3 digit number up to 100 which
equals the “+” value tolerance of the capacitor or
inductor under test. If a decimal is included, the
LC103 will round to the nearest whole number.
2. Press the white " + %" COMPONENT
PARAMETERS button. The “+” tolerance will now
be shown on the COMPONENT SETUP display.
3. Enter a 1 or 2 digit number up to 99 which equals to
the “-“ value tolerance of the capacitor or inductor. If
a decimal is included, the LC103 will round to the
nearest whole number.
4. Press the white " - %" COMPONENT
PARAMETERS button. The “-“ tolerance will now
be shown on the COMPONENT SETUP display.
NOTE: If the “+” and “-“ tolerances are the same,
simply enter that value and press the “+%” button
followed by the “-%” button.
To enter leakage voltage:
1. Enter the desired voltage from 1 to 1000 using the
gray keys on the NUMERIC INPUT keypad. A
decimal, followed by one digit may be entered, but is
not necessary.
2. Push the white “V” key to enter the voltage. The
voltage will be shown on the COMPONENT SETUP
display. For values greater than 25 volts the red
WARNING indicator LED will blink.
NOTE: The voltage is applied to the component Test
Leads when the CAPACITOR LEAKAGE test button is
pushed.
3. To enter a different voltage, repeat steps 1 & 2.
WARNING INDICATION
The Warning Indicator LED on the LC103 front
panel alerts the user that 25-1,000 V will be applied
to the test leads when the leakage button is pressed.
Fig. 11: Example of entering component data for an
Aluminum Electrolytic: (a) Component Type = Aluminum
Lytics; (b) Value = 100 uF; (c) Tolerance = +20%, -20%; (d)
Leakage Voltage = 250V.
!
!
LC103
COMPONENT SETUP
COMPONENT TYPE
LEAD FUSE TEST LEAD LEAD ZERO
NUMERIC INPUT ENTER IN-CIRCUIT OUT-OF-CIRCUIT
COMPONENT PARAMETERS COMPONENT TESTS
COMPONENT TEST RESULTS
CAPACITOR & INDUCTOR ANALYZER
POWER
HOLD FOR
BATTERY
TEST
ALUMINUM
LYTICS
DOUBLE
LAYER
LYTICS
HIGH R
DOUBLE
LAYER
1234pFµFF
CAPACITOR
GOOD/BAD
INDUCTOR
GOOD/BAD
CAPACITOR
VAL UE
CAPACITOR
ESR
CAPACITOR
LEAKAGE
INDUCTOR
RINGER
DIELECTRIC
ABSORPTION
INDUCTOR
VAL UE
+ % - % V
µH mH H
5678
90 •CLR
ALL
OTHER
CAPS
SWITCHING
TRANS-
FORMERS
TANTALUM
CAPS
CERAMIC
CAPS
YOKES &
FLYBACKS
COILS
1A, TT
2 AG, BLO BLO
0-1000 V
500 mA
REMOTE
OPEN
RANGES: 1pF to 20 F, 0.1 µH to 20 H Patent Nos. 4258315, 4287503, 4795966, 4825147, 5717338, Others Pending
WARNING: Flashing light indicates 25-1000V
applied to test leads when leakage button is pressed.
STOP TESTING: Protection circuit or fuse is open.
Capacitor being tested may be charged. Carefully
discharge capacitor and check fuse.
SHORT
F
U
S
E
F
U
S
E
Alum Lytics READY
PULL CHART
ALUMINUM
LYTICS
!
!
LC103
COMPONENT SETUP
COMPONENT TYPE
LEAD FUSE TEST LEAD LEAD ZERO
NUMERIC INPUT ENTER IN-CIRCUIT OUT-OF-CIRCUIT
COMPONENT PARAMETERS COMPONENT TESTS
COMPONENT TEST RESULTS
CAPACITOR & INDUCTOR ANALYZER
POWER
HOLD FOR
BATTERY
TEST
ALUMINUM
LYTICS
DOUBLE
LAYER
LYT I C S
HIGHER
DOUBLE
LAYER
1234pFµFF
CAPACITOR
GOOD/BAD
INDUCTOR
GOOD/BAD
CAPACITOR
VAL UE
CAPACITOR
ESR
CAPACITOR
LEAKAGE
INDUCTOR
RINGER
DIELECTRIC
ABSORPTION
INDUCTOR
VAL UE
+ % - % V
µH mH H
5678
90
1µF
0
0
•CLR
ALL
OTHER
CAPS
SWITCHING
TRANS-
FORMERS
TANTALUM
CAPS
CERAMIC
CAPS
YOKES &
FLYBACKS
COILS
1A, TT
2 AG, BLO BLO
0-1000 V
500 mA
REMOTE
OPEN
RANGES: 1pF to 20 F, 0.1 µH to 20 H Patent Nos. 4258315, 4287503, 4795966, 4825147, 5717338, Others Pending
WARNING: Flashing light indicates 25-1000V
applied to test leads when leakage button is pressed.
STOP TESTING: Protection circuit or fuse is open.
Capacitor being tested may be charged. Carefully
discharge capacitor and check fuse.
SHORT
F
U
S
E
F
U
S
E
Alum Lytics 100 μ F READY
PULL CHART
!
!
LC103
COMPONENT SETUP
COMPONENT TYPE
LEAD FUSE TEST LEAD LEAD ZERO
NUMERIC INPUT ENTER IN-CIRCUIT OUT-OF-CIRCUIT
COMPONENT PARAMETERS COMPONENT TESTS
COMPONENT TEST RESULTS
CAPACITOR & INDUCTOR ANALYZER
POWER
HOLD FOR
BATTERY
TEST
ALUMINUM
LYTICS
DOUBLE
LAYER
LYT I C S
HIGHER
DOUBLE
LAYER
1234 µFF
CAPACITOR
GOOD/BAD
INDUCTOR
GOOD/BAD
CAPACITOR
VAL UE
CAPACITOR
ESR
CAPACITOR
LEAKAGE
INDUCTOR
RINGER
DIELECTRIC
ABSORPTION
INDUCTOR
VAL UE
+ % - %
mH H
5678
90 •CLR
ALL
OTHER
CAPS
SWITCHING
TRANS-
FORMERS
TANTALUM
CAPS
CERAMIC
CAPS
YOKES &
FLYBACKS
COILS
1A, TT
2 AG, BLO BLO
0-1000 V
500 mA
REMOTE
OPEN
RANGES: 1pF to 20 F, 0.1 µH to 20 H Patent Nos. 4258315, 4287503, 4795966, 4825147, 5717338, Others Pending
WARNING: Flashing light indicates 25-1000V
applied to test leads when leakage button is pressed.
STOP TESTING: Protection circuit or fuse is open.
Capacitor being tested may be charged. Carefully
discharge capacitor and check fuse.
SHORT
F
U
S
E
F
U
S
E
Alum Lytic 100 μ F
+20% -20%
READY
PULL CHART
!
!
LC103
COMPONENT SETUP
COMPONENT TYPE
LEAD FUSE TEST LEAD LEAD ZERO
NUMERIC INPUT ENTER IN-CIRCUIT OUT-OF-CIRCUIT
COMPONENT PARAMETERS COMPONENT TESTS
COMPONENT TEST RESULTS
CAPACITOR & INDUCTOR ANALYZER
POWER
HOLD FOR
BATTERY
TEST
ALUMINUM
LYTICS
DOUBLE
LAYER
LYT I C S
HIGHER
DOUBLE
LAYER
1234pFµFF
CAPACITOR
GOOD/BAD
INDUCTOR
GOOD/BAD
CAPACITOR
VAL UE
CAPACITOR
ESR
CAPACITOR
LEAKAGE
INDUCTOR
RINGER
DIELECTRIC
ABSORPTION
INDUCTOR
VAL UE
+ % - % V
µH mH H
5678
90 •CLR
ALL
OTHER
CAPS
SWITCHING
TRANS-
FORMERS
TANTALUM
CAPS
CERAMIC
CAPS
YOKES &
FLYBACKS
COILS
1A, TT
2 AG, BLO BLO
0-1000 V
500 mA
REMOTE
OPEN
RANGES: 1pF to 20 F, 0.1 µH to 20 H Patent Nos. 4258315, 4287503, 4795966, 4825147, 5717338, Others Pending
WARNING: Flashing light indicates 25-1000V
applied to test leads when leakage button is pressed.
STOP TESTING: Protection circuit or fuse is open.
Capacitor being tested may be charged. Carefully
discharge capacitor and check fuse.
SHORT
F
U
S
E
F
U
S
E
Alum Lytic 100 μ F
+20% -20% 50V
READY
PULL CHART
a. Enter Component Type
b. Enter Component Value
2- %
0
+ %
c. Enter Component Tolerance
2V
5
0
d. Enter Leakage Voltage

Sencore ReZolver LC103 Specifications

General

Brand	Sencore
Model	ReZolver LC103
Category	Measuring Instruments
Language	English