Why is my Servend CT-6 only dispensing water?
If your Servend Dispenser is only dispensing water, it could be due to several reasons: * **No pressure:** Check and adjust the regulator(s). * **Out of CO2:** Install a fresh CO2 tank. * **Defective regulator(s):** Check, repair, or replace the regulator(s). * **CO2 line pinched, kinked, or obstructed:** Check, repair, or replace the CO2 line.
Why are the drinks foaming from my Servend CT-6 Dispenser?
If the drinks from your Servend Dispenser are foaming, it could be due to: * **Incorrect system pressures:** Check the CO2 supply and reset the pressure, or replace the regulator if necessary. * **Dirty lines/valves:** Clean and sanitize the entire system.
How to fix a Servend CT-6 Dispenser beverage that is too sweet?
If the beverage dispensed from your Servend Dispenser is too sweet, consider these potential causes: * **Incorrect drink ratio (brix):** Adjust the flow control. * **Insufficient soda flow due to low carbonator pressure:** Adjust the CO2 pressure or change the tank. * **Low CO2 pressure due to leaks:** Repair CO2 leaks. * **Obstruction in the water or soda line:** Clean out the lines.
What to do if the beverage from my Servend CT-6 Dispenser is not sweet enough?
If the beverage from your Servend Dispenser is not sweet enough, check the following: * **Incorrect drink ratio (brix):** Adjust the flow control. * **Soda flow too high:** Reset CO2 pressure or replace the regulator if necessary. * **Obstruction in syrup line:** Clean out the syrup line.
Why is my Servend CT-6 Dispenser only dispensing syrup and plain water?
If your Servend Dispenser is dispensing only syrup and plain water, it could be due to: * **No pressure:** Install a fresh tank. * **HP regulator out of adjustment:** Adjust the HP regulator to the proper setting. * **Defective HP regulator:** Check, repair, or replace the HP regulator. * **CO line pinched, kinked or obstructed:** Check, repair, or replace the CO line.
Why is my Servend CT-6 Dispenser not dispensing water, syrup, or gas?
If your Servend Dispenser is not dispensing any water, syrup, or gas, check these potential issues: * **No power to the unit:** Plug in the unit or reset the breaker. * **Power to control box:** Replace the fuse or control box. * **Power not coming through the key switch:** Turn the switch “on.” * **Key switch defective:** Replace the key switch. * **No power to the key switch:** Reset or replace the transformer.
Why won't one valve on my Servend CT-6 dispense anything?
If one valve on your Servend Dispenser is not dispensing anything, consider the following: * **No power to the valve:** Replace or repair the wire or connector. * **Bad microswitch:** Replace the microswitch.
Why doesn't the pump motor shut off on my Servend CT-6 Dispenser?
If the pump motor on your Servend Dispenser does not shut off, it could be due to a problem with the probe or probe harness. Try these steps: 1. Remove the probe electronics. 2. Pass the magnetic tip of a screwdriver by the lower end of the tube extending from the electronics package. 3. The reed switch will close. 4. The carbonator operates.
What to do if my Servend Dispenser is dispensing only syrup and CO2?
If your Servend Dispenser is dispensing only syrup and CO2, there might be an issue with the water supply or power. Here are some things to check: * **No power:** Check the power supply. Plug in the carbonator or reset the breaker. * **Water supply:** Ensure the water is turned “on.” Replace the water filter. Check, clean, or replace the pump strainer. Check, clean, or repair the water check valve. Check for a frozen water line (internal carbonator unit only). * **Defective carbonator:** Check, repair, or replace the carbonator pump, motor, electrode, or liquid level control.
Why is the pump motor on my Servend CT-6 not pumping?
If the pump motor on your Servend Dispenser is not pumping, it could be because the water pressure from the water source is not high enough. Make sure the water pressure leading into the pump inlet is 40 psi minimum.
To Next Page
General