Siemens 7VK512

6+
)NSTALLATION INSTRUCTIONS
6

#
' #
 -OUNTING AND CONNECTIONS
 -ODEL 6+J J"JJJ FOR PANEL SUR
FACE MOUNTING
3ECURE THE UNIT WITH FOUR SCREWS TO THE PANEL &OR
THE DIMENSIONS REFER TO &IGURE 
#ONNECT THE EARTHING TERMINAL 4ERMINAL  OF THE
UNIT TO THE PROTECTIVE EARTH OF THE PANEL
-AKE A SOLID LOW OHMIC AND LOW INDUCTANCE
OPERATIONAL EARTH CONNECTION BETWEEN THE EARTH
ING SURFACE AT THE SIDE OF THE UNIT USING AT LEAST ONE
STANDARD SCREW - AND THE EARTHING CONTINUITY
SYSTEM OF THE PANEL RECOMMENDED GROUNDING
STRAP $).  FORM ! EG /RDER
.O  OF
-ESSRS $RUSEIDT 2EMSCHEID 'ERMANY
-AKE CONNECTIONS VIA SCREWED TERMINALS
 -ODEL 6+J
J#JJJ FOR PANEL FLUSH
MOUNTING OR J%JJJ FOR CUBICLE INSTALLA
TION
,IFT UP BOTH LABELLING STRIPS ON THE LID OF THE UNIT
AND REMOVE COVER TO GAIN ACCESS TO THE FOUR HOLES
FOR THE FIXING SCREWS
)NSERT THE UNIT INTO THE PANEL CUT OUT AND SECURE IT
WITH THE FIXING SCREWS &OR THE DIMENSIONS REFER TO
&IGURE 
#ONNECT THE EARTHING SCREW ON THE REAR OF THE UNIT
TO THE PROTECTIVE EARTH OF THE PANEL OR CUBICLE
-AKE A SOLID LOW OHMIC AND LOW INDUCTANCE
OPERATIONAL EARTH CONNECTION BETWEEN THE EARTH
ING SURFACE AT THE REAR OF THE UNIT USING AT LEAST ONE
STANDARD SCREW - AND THE EARTHING CONTINUITY
SYSTEM OF THE PANEL OR CUBICLE RECOMMENDED
GROUNDING STRAP $).  FORM ! EG /RDER
.O  OF -ESSRS $RUSEIDT 2EMSCHEID 'ER
MANY
-AKE CONNECTIONS VIA THE SCREWED OR SNAP IN
TERMINALS OF THE SOCKETS OF THE HOUSING /BSERVE
LABELLING OF THE INDIVIDUAL CONNECTOR MODULES TO
ENSURE CORRECT LOCATION OBSERVE THE MAX PERMIS
SIBLE CONDUCTOR CROSS
SECTIONS 4HE USE OF THE
SCREWED TERMINALS IS RECOMMENDED SNAP
IN
CONNECTION REQUIRES SPECIAL TOOLS AND MUST NOT BE
USED FOR FIELD WIRING UNLESS PROPER STRAIN RELIEF AND
THE PERMISSIBLE BENDING RADIUS ARE OBSERVED
 #HECKING THE RATED DATA
4HE RATED DATA OF THE UNIT MUST BE CHECKED AGAINST
THE PLANT DATA 4HIS APPLIES IN PARTICULAR TO THE RATED
DC VOLTAGE OF THE SUBSTATION BATTERY
 #ONTROL DC VOLTAGE OF BINARY INPUTS
7HEN DELIVERED FROM THE FACTORY THE BINARY INPUTS
ARE DESIGNED TO OPERATE IN THE TOTAL CONTROL VOLTAGE
RANGE FROM  6 TO  6 )F THE RATED CONTROL VOLTAGE
FOR THE BINARY INPUTS IS  6 OR HIGHER IT IS ADVISABLE
TO SELECT A HIGHER PICK
UP THRESHOLD TO THESE INPUTS
TO INCREASE STABILITY AGAINST STRAY VOLTAGES IN THE DC
CIRCUITS
4O SELECT A HIGHER PICK
UP THRESHOLD OF APPROXI
MATELY  6 FOR A BINARY INPUT A SOLDER BRIDGE MUST
BE REMOVED &IGURE  SHOWS THE ALLOCATION OF
THESE SOLDER BRIDGES FOR THE INPUTS ")  TO ")  AND
THEIR LOCATION ON THE BASIC PCB OF THE MODULE
%03
 &IGURE  SHOWS THE ASSIGNMENT OF THESE
SOLDER BRIDGES FOR THE INPUTS ")  TO ")  AND THEIR
LOCATION ON THE ADDITIONAL PCB %!:
 OF THE
MODULE
/PEN HOUSING COVER
,OOSEN THE BASIC MODULE USING THE PULLING AIDS
PROVIDED AT THE TOP AND BOTTOM
%LECTROSTATIC DISCHARGES VIA THE COMPO
NENT CONNECTIONS THE 0#" TRACKS OR THE
CONNECTING PINS OF THE MODULES MUST BE
AVOIDED UNDER ALL CIRCUMSTANCES BY PRE
VIOUSLY TOUCHING AN EARTHED METAL SUR
FACE

#AUTION
0ULL OUT MODULE AND PLACE ONTO A CONDUCTIVE SUR
FACE
#HECK THE SOLDER BRIDGES ACCORDING TO &IGURE 
AND  REMOVE BRIDGES WHERE NECESSARY
)NSERT MODULE INTO THE HOUSING ENSURE THAT THE RE
LEASING LEVER IS PUSHED FULLY TO THE RIGHT BEFORE THE
MODULE IS PRESSED IN
&IRMLY PUSH IN THE MODULE USING THE RELEASING LE
VER
#LOSE HOUSING COVER