6+
)NSTALLATION INSTRUCTIONS
6
#
' #
#ONFIGURATION OF OPERATIONAL FUNCTIONS
/PERATIONAL PRECONDITIONS
&OR MOST OPERATIONAL FUNCTIONS THE INPUT OF A CODE
WORD IS NECESSARY 4HIS APPLIES FOR ALL ENTRIES VIA THE
MEMBRANE KEYBOARD OR FRONT INTERFACE WHICH CON
CERN THE OPERATION ON THE RELAY FOR EXAMPLE
CONFIGURATION PARAMETERS FOR OPERATION LANGUAGE
,3! CONFIGURATION AND DEVICE CONFIGURATION
ALLOCATION OR MARSHALLING OF ANNUNCIATION SIGNALS
BINARY INPUTS OPTICAL INDICATIONS
SETTING OF FUNCTIONAL PARAMETERS THRESHOLDS
FUNCTIONS
4HE CODEWORD IS NOT REQUIRED FOR THE READ
OUT OF AN
NUNCIATIONS OPERATING DATA OR FAULT DATA OR FOR THE
READ
OUT OF SETTING PARAMETERS
4O INDICATE AUTHORIZED OPERATOR USE PRESS KEY #7
ENTER THE SIX FIGURE CODE AND CONFIRM
WITH % #ODEWORD ENTRY CAN ALSO BE MADE RETRO
SPECTIVELY AFTER PAGING OR DIRECT ADDRESSING TO ANY
SETTING ADDRESS
%.4%2 #/$%7/2$
#7 !##%04%$
#/$%7/2$ 72/.'
4HE ENTERED CHARACTERS DO NOT APPEAR IN THE DISPLAY
INSTEAD ONLY A SYMBOL APPEARS !FTER CONFIRMATION OF
THE CORRECT INPUT WITH % THE DISPLAY RESPONDS WITH #7
!##%04%$ 0RESS THE ENTRY KEY % AGAIN
)F THE CODEWORD IS NOT CORRECT THE DISPLAY SHOWS
#/$%7/2$ 72/.' 0RESSING THE #7 KEY ALLOWS
ANOTHER ATTEMPT AT CODEWORD ENTRY
3ETTINGS FOR OPERATING PARAMETERS ADDRESS BLOCK
/PERATING PARAMETERS CAN BE SET IN ADDRESS BLOCK
4HIS BLOCK ALLOWS THE OPERATOR LANGUAGE TO BE
CHANGED 4HE TRANSMISSION SPEED FOR TRANSFER OF
DATA TO A PERSONAL COMPUTER CAN BE MATCHED TO THE
INTERFACE OF THE 0# MESSAGES ON THE FRONT DISPLAY
CAN BE SELECTED HERE FOR THE QUIESCENT STATE OF THE
UNIT OR AFTER A FAULT EVENT 4O CHANGE ANY OF THESE PA
RAMETERS CODEWORD ENTRY IS NECESSARY
4HE SIMPLEST WAY OF ARRIVING AT THE BEGINNING OF THIS
CONFIGURATION BLOCK IS TO USE KEY $! FOLLOWED BY THE
ADDRESS NUMBER AND %.4%2 KEY % 4HE AD
DRESS APPEARS SEE BELOW +EY ! WILL TAKE THE
OPERATOR TO ADDRESS
4HE DISPLAY SHOWS THE FOUR
DIGIT ADDRESS NUMBER
IE BLOCK AND SEQUENCE NUMBER 4HE TITLE OF THE RE
QUESTED PARAMETER APPEARS BEHIND THE BAR SEE BE
LOW 4HE SECOND LINE OF THE DISPLAY SHOWS THE TEXT
APPLICABLE TO THE PARAMETER 4HE PRESENT TEXT CAN BE
REJECTED BY THE
.O KEY . 4HE NEXT TEXT CHOICE
THEN APPEARS AS SHOWN IN THE BOXES BELOW 4HE
CHOSEN ALTERNATIVE MUST BE CONFIRMED WITH ENTER
KEY %
7HEN THE RELAY IS DELIVERED FROM THE FACTORY THE DE
VICE IS PROGRAMMED TO GIVE FUNCTION NAMES AND OUT
PUTS IN THE 'ERMAN LANGUAGE 4HIS CAN BE CHANGED
UNDER ADDRESS 4HE OPERATOR LANGUAGES AVAIL
ABLE AT PRESENT ARE SHOWN IN THE BOXES BELOW
4HE SETTING PROCEDURE CAN BE ENDED AT ANY TIME BY
THE KEY COMBINATION &% IE DEPRESSING THE FUNCTION
KEY & FOLLOWED BY THE ENTRY KEY % 4HE DISPLAY SHOWS
THE QUESTION
3!6% .%7 3%44).'3 #ONFIRM
WITH THE
9ES KEY 9 THAT THE NEW SETTINGS SHALL BE
COME VALID NOW )F YOU PRESS THE
.O KEY . IN
STEAD CODEWORD OPERATION WILL BE ABORTED IE ALL AL
TERATIONS WHICH HAVE BEEN CHANGED SINCE THE LAST
CODEWORD ENTRY ARE LOST 4HUS ERRONEOUS ALTERATIONS
CAN BE MADE INEFFECTIVE
To Next Page
Loading...
