Siemens Clinitek Advantus Operator's Guide

22
44
CC
ll
ii
nn
ii
tt
ee
kk
AA
dd
vv
aa
nn
tt
uu
s s
OO
pp
ee
rr
aa
tt
oo
rr
’’
s s
GG
uu
ii
dd
ee
OO
pp
ee
rr
aa
tt
ii
nn
gg
tt
hh
ee
SS
yy
ss
tt
ee
mm
Performing a STAT TestPerforming a STAT Test
Use this procedure to run a STAT test when using a loadlist. After the STATUse this procedure to run a STAT test when using a loadlist. After the STAT
test the analyzer will continue testing specimens from the loadlist.test the analyzer will continue testing specimens from the loadlist.
1.1.
At At
the the
ReaRea
dy/dy/
Run Run
scrscr
eeneen
, s, s
eleele
ctct
STATSTAT
..
2.2.
EntEnt
er aer a
n ID n ID
for for
the the
STST
AA
T teT te
st.st.
The SEQ # shown is The SEQ # shown is
the next number available after the end of the the next number available after the end of the
loadlist.loadlist.
3.3.
EdEd
it the coit the co
lor alor a
nd cland cla
ritrit
yy
, if nec, if nec
essaessa
ryry
..
4.4.
SeSe
lele
ct ct
a ra r
eaea
gege
nt nt
stst
riri
p.p.
5.5.
DiDi
p anp an
d pld pl
acac
e a ree a re
agag
enen
t stt st
riri
p.p.
The result is The result is
printed when the STAprinted when the STA
T test is T test is
complete. The analyzercomplete. The analyzer
displays any confirmatory or displays any confirmatory or
microscopic flags from the microscopic flags from the
STST
AA
T test.T test.
6.6.
Run aRun a
nothenothe
r STr ST
AA
T test T test
or resuor resu
me lome lo
adlisadlis
t testt test
ing.ing.
The next test is allocated the SEQ # which follows the number used for theThe next test is allocated the SEQ # which follows the number used for the
STAT test just completed.STAT test just completed.
Cancelling a RunCancelling a Run
SelectSelect
Stop RunStop Run
if you need to stop if you need to stop
the run before all readings are complete.the run before all readings are complete.
YY
ou can cancel the entire run ou can cancel the entire run
or only the last strip placed on or only the last strip placed on
the platform.the platform.
If the you cancel the entire run, If the you cancel the entire run,
all strips on the platform are movedall strips on the platform are moved
immediately to the waste bin. No results are reported. No SEQ immediately to the waste bin. No results are reported. No SEQ
# is assigned# is assigned
for any strip that was not for any strip that was not
read at both readheads before Stop Run wasread at both readheads before Stop Run was
selected. Yselected. Y
ou must retest ou must retest
all the specimens for all the specimens for
all cancelled strips.all cancelled strips.
If only the last strip is cancelled, the run coIf only the last strip is cancelled, the run co
ntinues and you can test a new stripntinues and you can test a new strip
using the same SEQ #.using the same SEQ #.
CAUTIONCAUTION
Do not use a reagent Do not use a reagent
strip other than the selected primary orstrip other than the selected primary or
alternative reagent strip. Only use Siemens Diagnostics brandalternative reagent strip. Only use Siemens Diagnostics brand
reagent strips. Use of other strips may cause reagent strips. Use of other strips may cause
erroneous results.erroneous results.

Siemens Clinitek Advantus Specifications

General

Test Types	Urinalysis
Interface	RS-232, USB
Calibration	Automatic calibration
Measurement Principle	Reflectance photometry
Sample Type	Urine
Power Supply	100-240 VAC, 50/60 Hz
Type	Urine analyzer
Display	Touchscreen
Reagent Type	Test strips
Measurement Parameters	Glucose, Bilirubin, Ketone, Specific Gravity, Blood, pH, Protein, Urobilinogen, Nitrite, Leukocytes