To Next Page

To Previous Page

5 / 96

BA 5030 en 02/2013

Contents

1. Technical data 8.....................................................

1.1 General technical data 8...............................................................

1.2 Marking of the gear unit designed in accordance with Directive 94/9/EC 9.....................

1.2.1 Ambient temperature 9................................................................

1.3 Configurations and weights 10...........................................................

1.3.1 Gearunit types 10.....................................................................

1.3.2 Weights 11...........................................................................

1.4 Measuringsurface soundpressure level 13...............................................

1.4.1 Measuringsurface soundpressure level for bevelhelical gear units (B...) with fan 13............

1.4.1.1 Measuringsurface soundpressure level for bevelhelical gear units (B...) without fan 14.........

1.4.1.2 Measuringsurface soundpressure level for helicalgear units (H...) with fan 15.................

1.4.1.3 Measuringsurface soundpressure level for helicalgear units (H...) without fan 16..............

2. General notes 17.....................................................

2.1 Introduction 17........................................................................

2.2 Copyright 17..........................................................................

3. Safety instructions 18.................................................

3.1 Obligations of the user 18...............................................................

3.2 Environmental protection 19.............................................................

3.3 Special dangers and personal protective equipment 20......................................

4. Transport and storage 21.............................................

4.1 Scope of supply 21....................................................................

4.2 Transport 21..........................................................................

4.3 Storing the gear unit 23.................................................................

4.4 Standard coating and preservation 24....................................................

4.4.1 Interior preservation with preservative agent 25............................................

4.4.2 Exterior preservation 25................................................................

5. Technical description 26..............................................

5.1 General description 26.................................................................

5.2 Output designs 27.....................................................................

5.3 Housing 27...........................................................................

5.4 Toothed components 30................................................................

5.5 Lubrication 30.........................................................................

5.5.1 Splash lubrication 30...................................................................

5.6 Shaft bearings 30......................................................................

5.7 Shaft seals 30.........................................................................

5.7.1 Radial shaftsealing rings 30............................................................

5.7.2 Taconite seal 31.......................................................................

5.8 Backstop 32..........................................................................

5.9 Torquelimiting backstop (special design) 33..............................................

5.10 Cooling 34............................................................................

5.10.1 Fan 34...............................................................................

5.10.2 Cooling coil 35........................................................................

5.10.3 Addon oilsupply system with air oilcooler 36.............................................

5.10.4 Addon oilsupply unit with water oilcooler 38..............................................

5.10.4.1 Pump 39.............................................................................

5.10.4.2 Water oilcooler 39.....................................................................

5.10.4.3 Filter 39..............................................................................

5.11 Oiltemperature monitoring 40...........................................................

5.12 Oillevel monitoring system 40...........................................................

5.13 Bearingmonitoring system 41...........................................................

5.14 Auxiliary drive 41......................................................................

5.14.1 Auxiliary drive, designed as a maintenance drive or load drive 42.............................

5.14.2 Overrunning clutch 44..................................................................

5.14.3 Gear unit with auxiliary drive and torquelimiting backstop 44.................................

Brand	Siemens
Model	FLENDER H SH Series
Category	Industrial Equipment
Language	English

Siemens FLENDER H SH Series User Manual

Table of Contents

Questions and Answers:

Siemens FLENDER H SH Series Specifications

Related product manuals