EasyManuals Logo

Siemens SIMATIC Operating Instructions

Siemens SIMATIC
182 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #174 background imageLoading...
Page #174 background image
Index
ET 200pro Distributed I/O System - Fail-Safe Modules
174 Operating Instructions, 05/2007, A5E00394073-02
B
Behavior
In the event of discrepancy, 60, 93, 111
On channel faults, 92,
110
On module failure, 38
When
a com
munication error occurs, 34
Behavior at dis
crepancy, 60, 93, 111
4/8 F-DI/4 F-DO DC24V/2A PROFIsafe, 92,
110
8/16 F-DI DC24V PROFIsafe, 59
Block diag
ra
m
4/8 F-DI/4 F-DO DC24V/2A PROFIsafe,
91
8/16 F-DI DC24V PROFIsafe, 58
CM IO 12 x M12, 52
CM IO 16 x M12, 50
Bl
ock
Diagram
CM F-IO 2 x M12,
54
C
Cable cross section, 27
Capacitive loads
Switching,
95
Causes of faults
4/8 F-DI/4 F-DO DC24V/2A PROFIsafe,
101
8/16 F-DI DC24V PROFIsafe, 82
CE Certification, 39
Certification
CE,
39
cULus,
40
Marine, 40
Certification
mark for Australia, 40
Channel
Disabled
,
33
Channel fault,
34
Channel grou
p fault, 33
Channel n
4/8 F-DI/4 F-DO DC24V/2A PROFIsa
fe,
92, 110
Channel n+4
4/8 F-DI/4 F-DO DC24V/2A PROFIsafe,
92, 110
Channel-spe
cific diagnostics
of F-modules,
36
Starting at byte 20 to byte 31 (F-Switch), 149
Channel-Spe
cific Diagnostics
Starting at byte 28 to byte 43,
148
Starting at byte 8 to byte 23 in diagnostic data, 145
Climatic envir
onmental conditions, 46
CM F-IO 2 x M12
Block diag
ram,
54
Terminal assignment, 108
CM F-IO 2 x M12 conne
ction module
Block Diagram,
54
Technical specifications, 54
CM IO 12 x M12
Block diag
ram,
52
Properties, 51
Technical specifications, 52
Termin
al assignment, 52
CM IO 12 x M12 conne
ction module
Block diagram,
52
Properties, 51, 52
Technical specifications, 52
CM IO 16 x
M12
Block diag
ram,
50
Properties, 49
Technical specifications, 51
Termin
al assignment,
50, 57
CM IO 16 x M12 conne
ction module
Block diagram,
50
Properties, 49
Technical specifications, 51
Termin
al assignment, 50
Terminal assignment, 57
Combination of standa
rd and F-modules, 19
Commissioning
Of ET 200pro
,
17
Communicati
on error, 29, 37
4/8 F-DI/4 F-DO DC24V/2A PROFIsafe, 100,
133
8/16 F-DI DC24V PROFIsafe, 81
Behavio
r of the F-DI module, 34
Conditions
For safety clas
s with 8/16 F-DI DC24V
PROFIsafe,
64, 115
Transport an
d storage of F-modules, 46
Configuration
ET 200pro with F-modules,
19
Configuration
example
Voltage group,
19
Configuring
F-mod
ules,
21
Connec
tion module
Terminal assignment,
29
Conv
entions
in this manual,
6
Corrective actions
4/8 F-DI/4 F-DO DC24V/2A PROFIs
afe,
101
8/16 F-DI DC24V PROFIsafe, 82
Cross
circuit
4/8 F-DI/4 F-DO DC24V/2A PROFIsafe,
98
CSA approval, 40
C-Tick
, 40
cULus
approval, 40

Table of Contents

Other manuals for Siemens SIMATIC

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SIMATIC and is the answer not in the manual?

Siemens SIMATIC Specifications

General IconGeneral
Product type designationSIMATIC
CPUVaries by model
MemoryVaries by model
Input/OutputVaries by model
CommunicationVaries by model
Programming LanguageSTEP 7
Operating Temperature0°C to 60°C (varies by model)
Protection ClassIP20
CategoryProgrammable Logic Controller (PLC)

Related product manuals