Siemens SINAMICS G120C User Manual

0RWRUL]HGSRWHQWLRPHWHUVHWSRLQW
DIWHUWKHUDPSIXQFWLRQJHQHUDWRU
0RWRUL]HGSRWHQWLRPHWHU
VHWSRLQWORZHU
0RWRUL]HGSRWHQWLRPHWHU
VHWSRLQWKLJKHU
,QSXWV2XWSXW3DUDPHWHU
S
U
S
023
FigureA-1 Example of a block: Motorized potentiometer (MOP)
Most of the blocks can be adapted to speci󹪝c applications using parameters.
You cannot change the signal interconnection within the block. However, the
interconnection between blocks can be changed by interconnecting the inputs of a block
with the appropriate outputs of another block.
The signal interconnection of the blocks is realized, contrary to electric circuitry, not using
cables, but in the software.
0DLQVHWSRLQW
0RWRUL]HGSRWHQWLRPHWHU
VHWSRLQWDIWHUWKH
UDPSIXQFWLRQJHQHUDWRU
0RWRUL]HG
SRWHQWLRPHWHU
VHWSRLQWORZHU
0RWRUL]HG
SRWHQWLRPHWHU
VHWSRLQWKLJKHU
352),GULYH
UHFHLYH3='
ELWE\ELW
S

U
U
S
U
S
023
FigureA-2 Example: Signal interconnection of two blocks for digital input 0
Binectors and connectors
Connectors and binectors are used to exchange signals between the individual blocks:
• Connectors are used to interconnect "analog" signals (e.g. MOP output speed)
• Binectors are used to interconnect digital signals (e.g. "Enable MOP up" command)
%,&2EORFN
%LQHFWRULQSXW
%LQHFWRURXWSXW
%LQHFWRUFRQQHFWRURXWSXW
&RQQHFWRURXWSXW
&RQQHFWRULQSXW
S[[[[
U[[[[
U[[[[
U[[[[
U[[[[
S[[[[
%,
&2
%2
&2%2
&,
FigureA-3 Symbols for binector and connector inputs and outputs
Binector/connector outputs (CO/BO) are parameters that combine more than one binector
output in a single word (e.g. r0052 CO/BO: status word 1). Each bit in the word represents
a digital (binary) signal. This summary reduces the number of parameters and simpli󹪝es
parameter assignment.
Binector or connector outputs (CO, BO or CO/BO) can be used more than once.
Appendix
A.2Interconnecting signals in the converter
SINAMICS G120C Converters
462 Operating Instructions, 02/2023, FW V4.7 SP14, A5E34263257B AK

Siemens SINAMICS G120C Specifications

General

Communication Interfaces	PROFINET, PROFIBUS, USS, Modbus RTU
Protection Class	IP20
Ambient Temperature	-10°C to +50°C
Storage Temperature	-40°C to +70°C
Power Range	0.55 kW to 132 kW
Voltage Range	380 V to 480 V
Output Voltage	0 V to Supply Voltage
Frequency Range	0 Hz to rated output frequency
Control Modes	Vector control with encoder
Protection	Overload, overvoltage, undervoltage, short circuit, ground fault
Relative Humidity	5% to 95%, non-condensing
Altitude	Up to 2000 m without derating