Siemens SINAMICS S120 - Selection and Ordering Data

Gearbox
9.2 Motors with planetary gears
Synchronous Motors 1FK7
196 Configuration Manual, (PFK7S), Edition 12.2006, 6SN1197-0AD16-0BP1
9.2.1.1 Selection and ordering data
Selection and ordering data, single-stage planetary gear, SP+ series
Motor
Natural
cooling
Planetary gearbox
single-stage
Available
gear ratio i
Max. perm.
motor speed
S3-60%
Max. perm.
output
torque
S3-60%
Max. perm.
radial output
shaft
load
1)
Max. perm.
axial output
shaft
load
1)
Type Type Tor-
sional
back-
lash
Weight of
gearbox,
approx.
4 5 7 10 n
G1
(n
1
)
M
G2
(T
2B
)
F
r
(F
2Rmax
)
F
a
(F
2Amax
)
arcmin kg/lb rpm Nm/lb
f
-ft N/lb
f
N/lb
f
1FK7022 SP 060S-MF1 ≤4 1.9/4.2 6000 40/29.5
(32/23.6 for i = 10)
2700/
606.99
2400/
539.54
1FK7032
1FK7033
1FK7034
1FK7040
1FK7042
1FK7043
1FK7044
SP 075S-MF1 ≤4 3.9/8.6 6000 110/81.1
(90/66.3 for i = 10)
4000/
899.24
3350/
753.11
1FK7060
1FK7061
1FK7063
1FK7064
SP 100S-MF1 ≤37.7/17.0 4500 300/221.1
(225/165.8 for i = 10)
6300/
1416.30
5650/
1270.18
1FK7080
1FK7082
1FK7083
1FK7085
1FK7086
SP 140S-MF1 ≤3 17.2/37.9 4000 600/442.2
(480/353.8 for i = 10)
9450/
2124.45
9870/
2218.87
1FK7100
1FK7101
1FK7103
1FK7105
SP 180S-MF1 ≤3 34/75.0
–
3500 1100/810.7 14700/
3304.71
14150/
3181.06
1FK7105
SP 210-MF1
2)
≤4 53/116.9 – –– 2200 2720/2004.6 18000/
4046.58
22500/
5058.23
Order codes
Gearbox shaft with fitted key J02 J03 J05 J09
Gearbox shaft without fitted key J22 J23 J25 J29
Ordering data 1FK7...-.A.71-1.. 7 5-Z Order No. of the motor with identifier “-Z” and
order code for mounting the planetary gearbox assigned to the motor
Prerequisite for mounting planetary gearboxes:
Plain motor shaft end IP65 degree of protection, anthracite paint finish
J
77
w/o holding brake
with holding brake
G
H
1)
In reference to the motor shaft center.
2)
With this version, the oil filling quantities depend on the mounting position. In the case of a vertical mounting position, the 12th position in the
Order No. should be “9” and a further order code also has to be specified: 1FK7...-.A.7 9-1.. 5-Z J.. + M1 7
H mounting position IM V1
G mounting position IM V3