Siemens SINAMICS S120 - Page 23

Motor Description
1.3 Selection and Ordering Data
Synchronous Motors 1FK7
Configuration Manual, (PFK7S), Edition 12.2006, 6SN1197-0AD16-0BP1
23
Motor type
(continued)
Static
current
Calculated
power
P
calc
= M
0
x
n
rated
/9550
SINAMICS Power Module Power cable with complete shield
Motor terminal (and brake terminal) via
power connector
Rated
output
current
I
0
at M
0
∆ T=100 K
P
calc
for M
0
∆T=100 K
I
rated
at M
0
∆T=100 K
Order No.
For complete order no.,
see “SINAMICS S120”
Power
con-
nector
Motor
cable cross
section
3)
Order no.
Pre-assembled cable
A kW/HP A Size mm
2
1FK7032-5AF21... 1.7 0.36/0.5 2.3 6SL3210 - 1SB12-3UA0 1 4 x 1.5 6FX 7 002-5 7 A01-....
1FK7033-7AF21...
1FK7034-5AF21...
2.2
1.9
0.41/0.6
0.5/0.7
2.3
2.3
6SL3210 - 1SB12-3UA0
6SL3210 - 1SB12-3UA0
1
1
4 x 1.5
4 x 1.5
6FX 7 002-5 7 A01-....
6FX
7 002-5 7 A01-....
1FK7042-5AF21...
1FK7043-7AF21...
3.9
3.9
0.94/1.3
0.85/1.1
3.9
3.9
6SL3210 - 1SB14-0UA0
6SL3210 - 1SB14-0UA0
1
1
4 x 1.5
4 x 1.5
6FX 7 002-5 7 A01-....
6FX
7 002-5 7 A01-....
1FK7011-5AK21...
1FK7015-5AK21...
0.85
0.85
0.11/0.2
0.22/0.3
0.9
0.9
6SL3210 - 1SB11-0UA0
6SL3210 - 1SB11-0UA0
0.5
0.5
4 x 1.5
4 x 1.5
6FX5002-5ME00-....
2)
6FX5002-5ME00-....
2)
1FK7022-5AK21... 1.8 0.53/0.7 2.3 6SL3210 - 1SB12-3UA0 1 4 x 1.5 6FX 7 002-5 7 A01-....
Cooling:
Internal air cooling
0
Motor Module:
Single Motor Module
1
Power cable model:
MOTION-CONNECT 800
MOTION-CONNECT 500
8
5
Without brake cores
With brake cores
C
D
For length code as well as power and signal cables, see “MOTION-CONNECT cables and connections”. ....
1)
If the absolute encoder is used, M
rated
is reduced by 10%.
2)
This power cable is fitted with a connector with M17 thread at the
motor end and brake cores as standard (4 x 1.5 mm
2
+ 2 x 1.5 mm
2
).
3)
The current carrying capacity of the power cable corresponds to
IEC 60204-1 for type of routing C under continuous operating condi-
tions with an ambient air temperature of +40 °C (104 °F), designed
for I
0
(100 K), PVC/PUR-insulated cable.
4)
Motors in shaft height 20 are not available with a DRIVE-CLiQ inter-
face. The encoder systems are connected via the SMC (Sensor
Module Cabinet-Mounted).