EasyManuals Logo

Siemens SINUMERIK 804D sl Function Manual

Siemens SINUMERIK 804D sl
2050 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #206 background imageLoading...
Page #206 background image
Contents
Acceleration (B2)
iv Function Manual, 08/2005 Edition, 6FC5397-0BP10-0BA0
2.6.2 Activation.................................................................................................................................. 2-12
2.6.3 Programming............................................................................................................................ 2-12
2.7 Acceleration with programmed rapid traverse (G00) (axis-specific)........................................ 2-13
2.7.1 Detailed description.................................................................................................................. 2-13
2.7.1.1 General information.................................................................................................................. 2-13
2.7.2 Activation.................................................................................................................................. 2-14
2.7.2.1 Parameterization ...................................................................................................................... 2-14
2.7.3 Programming............................................................................................................................ 2-14
2.8 Acceleration with active jerk limitation (SOFT/SOFTA) (axis-specific) .................................... 2-14
2.8.1 Detailed description.................................................................................................................. 2-14
2.8.1.1 General information.................................................................................................................. 2-14
2.8.2 Activation.................................................................................................................................. 2-15
2.8.2.1 Parameterization ...................................................................................................................... 2-15
2.8.3 Programming............................................................................................................................ 2-15
2.9 Excessive acceleration for non-tangential block transitions (axis-specific) ............................. 2-16
2.9.1 Detailed description.................................................................................................................. 2-16
2.9.1.1 General information.................................................................................................................. 2-16
2.9.2 Activation.................................................................................................................................. 2-16
2.9.2.1 Parameterization ...................................................................................................................... 2-16
2.9.3 Programming............................................................................................................................ 2-17
2.10 Acceleration margin for radial acceleration (channel-specific) ................................................ 2-17
2.10.1 Detailed description.................................................................................................................. 2-17
2.10.1.1 General information.................................................................................................................. 2-17
2.10.2 Activation.................................................................................................................................. 2-19
2.10.2.1 Parameterization ...................................................................................................................... 2-19
2.10.3 Programming............................................................................................................................ 2-19
2.11 Jerk limitation with path interpolation (SOFT) (channel-specific)............................................. 2-19
2.11.1 Detailed description.................................................................................................................. 2-19
2.11.1.1 General information.................................................................................................................. 2-19
2.11.1.2 Maximum jerk value (axis-specific) .......................................................................................... 2-21
2.11.1.3 Maximal jerk value (canal-specific) ..................................................................................
........ 2-21
2.11.2 Activation.................................................................................................................................. 2-22
2.11.2.1 Parameterization ...................................................................................................................... 2-22
2.11.3 Programming............................................................................................................................ 2-22
2.12 Jerk limitation with single-axis interpolation (SOFTA) (axis-specific) ...................................... 2-23
2.12.1 Detailed description.................................................................................................................. 2-23
2.12.1.1 General information.................................................................................................................. 2-23
2.12.2 Activation.................................................................................................................................. 2-23
2.12.2.1 Parameterization ...................................................................................................................... 2-23
2.12.3 Programming............................................................................................................................ 2-23
2.13 Path-jerk limitation (channel-specific) ...................................................................................... 2-24
2.13.1 Detailed description.................................................................................................................. 2-24
2.13.1.1 General information.................................................................................................................. 2-24
2.13.2 Activation.................................................................................................................................. 2-25
2.13.2.1 Parameterization ...................................................................................................................... 2-25
2.13.3 Programming............................................................................................................................ 2-25
2.13.3.1 Maximum path-jerk................................................................................................................... 2-25
2.13.3.2 Activation/Deactivation............................................................................................................. 2-25
2.14 Path jerk for real-time events (channel-specific)...................................................................... 2-26
2.14.1 Detailed description.................................................................................................................. 2-26
2.14.1.1 General information.................................................................................................................. 2-26
2.14.2 Activation.................................................................................................................................. 2-27
2.14.3 Programming............................................................................................................................ 2-27

Table of Contents

Other manuals for Siemens SINUMERIK 804D sl

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINUMERIK 804D sl and is the answer not in the manual?

Siemens SINUMERIK 804D sl Specifications

General IconGeneral
BrandSiemens
ModelSINUMERIK 804D sl
CategoryControl Systems
LanguageEnglish

Related product manuals