EasyManua.ls Logo

Simrad E5024 ECDIS User Manual

Simrad E5024 ECDIS
43 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
ENGLISH
E5024 ECDIS System
Installation Manual
Question and Answer IconNeed help?

Do you have a question about the Simrad E5024 ECDIS and is the answer not in the manual?

Simrad E5024 ECDIS Specifications

General IconGeneral
Display Size24 inches
TypeLCD
Operating SystemWindows Embedded
ECDIS StandardIEC 61174
Operating Voltage24 VDC

Summary

Warnings and Manual Guidance

Safety Warnings

Cautionary notes regarding equipment operation and potential interference.

E5024 System Overview

E5000 CPU Architecture

Description of the E5000 processor's dual CPU setup and capabilities.

E5000 Box Contents

E5000 ECDIS Processor

The main processing unit included in the E5000 box.

E5000 CPU Port Details

ECDIS CPU Port Layout

Diagram and description of ports specific to the ECDIS CPU.

NSO evo2 CPU Port Layout

Diagram and description of ports specific to the NSO evo2 CPU.

Hardware Installation Procedures

Mounting Location Selection

Guidelines for choosing an appropriate and safe mounting spot.

E5000 Processor Mounting

Instructions for physically securing the E5000 processor unit.

Wiring Guidelines and Connections

General Wiring Best Practices

Do's and don'ts for routing and securing cables.

E5000 Power Connection

Details on connecting the E5000 processor to the DC power supply.

External Alarm Wiring

Instructions for connecting the external alarm output.

External Alarm and Power Connections

External Alarm Wiring Diagram

Shows the connection for the E5000's blue alarm pin.

Monitor Connectivity

Connecting Displays via HDMI

How to connect two displays using HDMI ports on the E5000.

Control and Network Connectivity

Connecting Control Devices

How to connect trackballs to the E5000's USB ports.

NMEA 2000 CAN Bus Overview

Introduction to NMEA 2000, its connectors, and network structure.

Planning NMEA 2000 Backbone

Steps for planning and installing the NMEA 2000 backbone.

NMEA 2000 CAN Bus Powering

Powering the CAN Bus Network

Details on supplying 12V DC power to the NMEA 2000 network.

Using S180 for CAN Bus Power

Guidance on using the S180 unit for powering the network.

NMEA 0183 Device Connections

E5000 NMEA 0183 Ports

Description of the four NMEA 0183 ports on the E5000 processor.

Serial Port Configuration

Details on configuring baud rate and serial settings for CPUs.

Chart Installation and Management

Installing Charts from NavStick

Procedure for installing charts from the included NavStick USB.

Chart Subscription and Updates

Copying Charts to E5024

Procedure to transfer charts and licenses from NavStick to the system.

ECDIS Software Setup

Vessel Configuration Settings

Performance Characteristics

Entering vessel dimensions and performance data for safety checks.

Vessel Parameters

Inputting unique vessel identification details like MMSI and IMO.

Sensor Configuration

Accessing the Web Interface

Connecting PC to E5000 via Ethernet

Steps for establishing a direct Ethernet connection to the E5000.

Radar Overlay Configuration

Enabling Radar Overlay

Instructions on how to enable radar PPI overlay on the chart.

System Settings Configuration

System Configuration Options

System Synchronization and Backup

Synchronizing ECDIS Units

Methods for synchronizing data between multiple ECDIS units.

Alarm Configuration

Grounding Check Settings

Configures the grounding check function and guard zone for hazard detection.

Supported Data Formats

NMEA 0183 Supported Sentences

Table of NMEA 0183 sentences supported by the E5000.

NMEA 2000 Supported Sentences

Table of NMEA 2000 data types supported by the E5000.

E5000 Processor Specifications

Interface Specifications

Details on Ethernet, NMEA 2000, Video, USB, and SD ports.

Related product manuals