What to do if SMART 450 enters Mixed Reality mode unexpectedly?
If SMART Notebook software unexpectedly enters Mixed Reality mode, press SMART Document Camera in the toolbar. Then, press Additional Settings and clear the selection of Automatically Start Mixed Reality Tools.
Why SMART Notebook doesn't detect my SMART 450 Document Camera?
If SMART Notebook software doesn’t detect your SMART Document Camera, ensure the USB cable is connected and the USB switch is correctly set. Verify that your software is up-to-date (at least SMART Notebook software 11 SP1). Check that the USB cable and the computer USB receptacle are working properly. Also, confirm that the USB to PC setting is set to CAMERA in the document camera's OSD menu.
How to fix dark and unreadable presentation screen on SMART 450?
If the presentation screen is dark and unreadable when using your SMART Document Camera, try the following: 1. Turn on Auto Image in the document camera’s on-screen display (OSD) menu (Menu > IMAGE > Advanced > Auto Image) to adjust the image brightness. 2. Reset your document camera to its default settings (Menu > SYSTEM > Default > Yes > Enter). 3. Ensure there’s enough light in the room, or turn on the overhead light on your document camera. 4. Manually adjust the brightness and contrast levels in the document camera's OSD menu, or use the control panel buttons. 5. If you are using a projector, check the bulb.
What to do if the image on SMART Document Camera is distorted or blurry?
To resolve a distorted or blurry image on the presentation screen when using your SMART Document Camera, reset your document camera to its default settings (Menu > SYSTEM > Default > Yes). Adjust the brightness and contrast manually to reduce the distortion. If the image is still blurry or out of focus, press the button on the control panel.
What to do if no camera image displays on SMART Document Camera?
If no camera image displays in Camera mode on your SMART Document Camera, ensure the document camera is turned on and check all cable connections. Verify the TV/VGA switch on the right-side connection panel is set to the correct display device. You can also reset the output resolution to 1024×768 by pressing the resolution reset button on the bottom of the document camera with a pen tip or other small object.
Why no computer image displays in Computer Pass-Through mode on SMART 450?
If no computer image displays in Computer Pass-Through mode on your SMART Document Camera, ensure the document camera is turned on and check all cable connections. Verify the cable connections from the computer VGA output to the VGA input of your document camera, and ensure the document camera is in Computer Pass-Through mode. For some laptop computers, you can press FN+F5 repeatedly to toggle between display modes to show the computer image on the presentation screen.
Why I'm unable to record a video on SMART Document Camera?
If you're unable to record a video with the SMART Document Camera (the red recording light doesn’t turn on), make sure an SD/SDHC card or USB drive is installed. The document camera does not record video while being used as a USB camera or mass storage device, so disconnect the USB cable.
What to do if SMART Document Camera doesn't detect the inserted USB drive?
If your SMART Document Camera doesn't detect the inserted USB drive, ensure the USB switch is set to the correct position.
How to fix SD/SDHC card or USB drive that doesn't play video properly on SMART 450?
If the SD/SDHC card or USB drive doesn't play video properly, or the SMART Document Camera stops responding during video recording, format the SD/SDHC card or USB drive using the document camera's OSD menu (Menu > SETTING > Format > SD CARD / USB DRIVE).
What to do if SMART 450 has an issue not described in manual?
If your SMART Document Camera has an issue not described, restart the document camera using the power button on the control panel.
General| Zoom | 8x digital zoom |
|---|---|
| Light Source | LED |
| Connectivity | USB |
| Output Interface | USB |
| Compatibility | Windows and Mac |
Essential safety precautions and warnings for product use and handling, including general warnings and cautions.
Details the capabilities, specifications, and technical features of the document camera.
Explains the different operational modes (Camera, Pass-Through, Playback) of the document camera.
Guides users through the physical setup and positioning of the document camera.
Details connections to display devices, computers, microscopes, and audio peripherals.
Information on using SD/SDHC cards and USB drives for storing captured images and videos.
Explains the functionalities and differences between the three camera operating modes.
Details navigation and available options within the Camera mode's OSD menu interface.
Covers how to save and transfer media files from the camera to storage or computer.
Explains how to integrate and use the document camera with SMART Notebook software.
Provides solutions for common issues encountered with the document camera, such as display problems.
To Next Page
