B-25
Center Attachment
45-360 INFIELD SCARIFIER WITH LONG VERTICAL BLADES PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 HHP-18 Bridge Pin,
1
/
8
3
2 HCP-12-200 Clevis Pin,
1
/
2
x 2 2
3 42-288 Left Castor Wheel Bracket 1
10-025 Flange Bushing (Part of 42-205) 2
HG-14-28-180 Grease Fitting,
1
/
4
- 28 x 180° (Part of 42-205) 1
4 HB-38-16-100 Hex Bolt,
3
/
8
- 16 x 1 12
HW-38 Flat Washer,
3
/
8
12
5 45-116 Center Lift Bar 1
6 42-241 Tine Segment 5
7 42-204 Castor Fork 2
8 HB-12-13-600 Hex Bolt,
1
/
2
-13 x 6 2
9 33-338 Axle Bearing 2
10 42-202 Tire and Wheel 2
11 HNTL-12-13 Nylon Lock Nut,
1
/
2
- 13 2
12 HCP-58-250 Clevis Pin,
5
/
8
x 2
1
/
2
1
13 HNTL-38-16 Nylon Lock Nut,
3
/
8
- 16 14
14 HMB-34-14 Machine Bushing,
3
/
4
x 14GA 2
15 42-289 Right Castor Wheel Bracket 1
10-025 Flange Bushing (Part of 42-206) 2
HG-14-28-180 Grease Fitting,
1
/
4
- 28 x 180° (Part of 42-206) 1
16 42-215 Short Spacer 2
17 HMB-34-10 Machine Bushing,
3
/
4
x 10GA 8
18 42-214 Long Spacer 2
19 42-539 Lynch Pin,
5
/
16
2
20 HB-38-16-125 Hex Bolt,
3
/
8
- 16 x 1
1
/
4
2
HW-38 Flat Washer,
3
/
8
2
INSTALLATION INSTRUCTIONS
1� Assemble the tine Segments (Ref 6) to the center lift bar (Ref 5) using the
3
/
8
- 16 x 1 bolts, washers
and nuts (Ref 4)�
2� Mount the right and left caster wheel brackets (Ref 3 and 15) to the center lift bar (Ref 5) using the rest
of
3
/
8
- 16 x 1 bolts, washers and nuts (Ref 4 & 13)� Mount the last two digger blades at this time using
the
3
/
8
- 16 x 1
1
/
4
bolts, washers and nuts (Ref 20 & 13)�
5� Extend hydraulic cylinder all the way down by pushing the lever forward�
6� Mount the rod end of the cylinder onto the center lift bar and secure with a clevis pin (Ref 12) and
bridge pin (Ref 1)�
7� Attach the arms on the center lift bar to the main frame on the machine and secure with clevis pin (Ref
2) and bridge pin (Ref 1)�
8� Turn machine on and test for proper operation�
9� Adjust castor wheels (Ref 12) by placing the short (Ref 16) or long spacer (Ref 18) on the castor wheel
fork before placing the castor wheel assembly into the castor wheel brackets� Be sure both castor
wheels are adjusted to the same height�
To Next Page
Loading...
