B-33
Center Attachment
45-175 ADJUSTABLE DISC EDGER PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 45-116 Center Lift 1
2 HHP-18 Bridge Pin,
1
/
8
3
3 HCP-58-250 Clevis Pin,
5
/
8
x 2
1
/
2
1
4 HB-38-16-125 Hex Bolt,
3
/
8
- 16 x 1
1
/
4
1
HW-38 Flat Washer,
3
/
8
1
HNTL-38-16 Nylon Lock Nut,
3
/
8
-16 1
5 HB-38-16-150 Hex Bolt,
3
/
8
- 16 x 1
1
/
2
2
HW-38 Flat Washer,
3
/
8
2
HNTL-38-16 Nylon Lock Nut,
3
/
8
- 16 2
6 45-166 Edger Mount 1
7 HB-12-13-150 Hex Bolt,
1
/
2
- 13 x 1
1
/
2
2
HW-12 Flat Washer,
1
/
2
2
HNTL-12-13 Nylon Lock Nut,
1
/
2
- 13 2
8 HP-18-150 Cotter Pin,
1
/
8
x 1
1
/
2
1
9 HNA-34-16 Axle Nut,
3
/
4
- 16 1
10 HMB-34-10 Machine Bushing,
3
/
4
x 10GA 4
11 13-204 Disc 1
12 13-205 Disc Flange 1
13 13-206 Spindle Shaft 1
14 13-391 Bearing and Collar 2
15 13-203 Spindle 1
HG-14-28-180 Grease Fitting 1
16 HW-716 Flat Washer,
7
/
16
1
17 HWL-38 Lock Washer,
3
/
8
1
18 HW-516 Flat Washer,
5
/
16
1
19 HB-38-16-100 Hex Bolt,
3
/
8
-16 x 1 1
20 HCP-12-200 Clevis Pin,
1
/
2
x 2 2
* Spindle Assembly
INSTALLATION INSTRUCTIONS
1� For initial assembly, bolt Spindle Assembly (Ref� 13 thru 19) to the Edger Mount (Ref� 6)� Use the
1
/
2
-
13 Bolts, Washers and Lock Nuts (Ref� 7) to secure�
2� Slide the Disc Flange (Ref� 12) on the Spindle Shaft (Ref� 13) up to the shoulder� Then place the Disc
(Ref�11) onto the shaft, orienting the concave side towards the Spindle followed by the four Machine
Bushings (Ref� 10), and the axle nut (Ref� 9)�
3� Tighten Axle Nut, insert and clinch the Cotter Pin (Ref� 8)�
4� Connect the Edger Mount onto the Center Lift (Ref�1) using the
3
/
8
Bolts, Washers and Lock Nuts (Refs�
4 & 5), with the 1
1
/
4
" Hex Bolt (Ref� 4) going into the last hole on the Mount Plate�
5� The Edger mounts under the center of the trap rake�
6� Start the engine and lower the cylinder for the attachment lift FULLY� Stop engine�
7� Slide Edger under the trap rake from the right side�
8� Position the lift arms on the attachment lift assembly to the lift brackets on the machine� Hold in place
with
1
/
2
x 2 clevis pin and bridge pins (Refs� 2 & 20)�
9� Attach the cylinder to the center tab on the Center Lift using the
5
/
8
x 2
1
/
2
Clevis Pin and Bridge Pin
(Refs� 2 & 3)�
10� Start engine and test lift and Edger to make sure all works well�
To Next Page
Loading...
