Sonicware LIVEN 8bit warps - Creating and Editing Waveforms; Editing Waveforms (Easy Mode); Auto-Advance Waveform Editing; Editing Waveforms (Advanced Mode)

Creating and editing waveforms
12
This section explains how to create and edit waveforms.
Editing waveforms (easy mode)
① While pressing , press WAVE EDIT.
A page button and step LED light, showing the posi
-
tion of the selected waveform.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• EDIT will appear on the display.
②
Turn the
VALUE knob, and select a waveform.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The waveform can also be selected by pressing
(U-01–U-16),
(U-17–U-32), (U-33–U-48) or
(U-49–U-64) to select the page, and then pressing
the step button.
• The waveform number (U-number) appears on the
display.
• The selection range is U-01–U-64.
③ Press
to enter waveform editing mode.
④ While pressing
, press to select EASY.
⑤ Turn the
VALUE knob to select the sample posi
tion to edit.
Step LED 1–16 will light according to the selected
sample value.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The sample position is shown on the display.
• The sample position range is 1–32.
⑥ Press a step button to set the parameter.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The step buttons show values as follows.
Step button 1 : － 128
Step button 2 : － 112
Step button 3 : － 96
Step button 4 : － 80
Step button 5 : － 64
Step button 6 : － 48
Step button 7 : － 32
Step button 8 : － 16
Step buttons 8 & 9 : 0
Step button 9 : 16
Step button 10 : 32
Step button 11 : 48
Step button 12 : 64
Step button 13 : 90
Step button 14 : 96
Step button 15 : 112
Step button 16 : 127
• If the waveform editing auto step function is en
-
abled, pressing the step button will automatically
move to the next sample position. (See p.12 “Au
-
tomatically advancing to the next sample during
waveform editing (waveform editing auto step)”.)
⑦ Repeat steps ⑤ and ⑥ , and press
.
⑧ Turn the
VALUE knob and select the waveform
number where it will be saved.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The waveform can also be selected by pressing
(U-01–U-16),
(U-17–U-32), (U-33–U-48) or
(U-49–U-64) to select the page, and then pressing
the step button.
• The waveform number (U-number) appears on the
display.
• The selection range is U-01–U-64.
⑨ Press
to save the waveform and end waveform
editing mode.
Automatically advancing to the next
sample during waveform editing
(waveform editing auto step)
① Follow steps ① – ④ in “Editing waveforms (easy
mode)”.
② Press
.
When in easy mode,
lights red if auto step is en-
abled.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• This can only be changed when in easy waveform
editing mode.
Editing waveforms (advanced mode)
① Follow steps ① – ③ in “Editing waveforms (easy
mode)”.
② While pressing
, press to select ADV.
③ Press a step button to select the sample position to
edit.
The LED for the selected step will light.