Sonicware LIVEN 8bit warps - Adjusting the Sound Parameters; Turning Filter On;Off; Changing Filter Type; Changing Filter Cutoff Frequency

Adjusting the sound
9
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• ON or OFF will appear on the display.
Turning the lter on/o󱐯
① While pressing , press .
Depending on the on/o󱐯 status, the
LED is lit/
unlit.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The lter type/OFF is shown on the display.
Changing the lter type
① While pressing , press a FILTER button.
The LED will light for the selected lter type.
(For BPF, both
and LEDs will light red.)
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• To select BPF, press
and at the same time.
• The lter type name is shown on the display.
• Three types of lters can be selected.
1. LPF : Filter the cuts high frequencies
2. HPF : Filter that cuts low frequencies
3. BPF : Filter that only allows through frequencies
in the specied band
Changing the lter cuto󱐯 frequency
① Turn the
CUTOFF/speed knob.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The parameter is shown on the display.
• The adjustment range is 0–127.
• The frequency can be changed in a range of 70–
21600Hz.
Adjusting the lter resonance
① Turn the
RESO/shift knob.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The parameter is shown on the display.
• For BPF, this adjusts the width of the band.
• The adjustment range is 0–127.
• The resonance can be changed in a range of 0.1–10.
• For BPF, the bandwidth can be changed in a 0.1–2.0
octave range.
Adjusting the LFO speed
① Turn the
RATE/speed knob.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The parameter is shown on the display.
• The LFO produces a sine wave.
• The adjustment range is 0–127.
• The frequency can be changed in a range of 0.1–30
Hz.
Adjusting the amount of LFO e󱐯ect on
pitch
① Turn the
PITCH/amount knob.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The parameter is shown on the display.
• The adjustment range is 0–127.
• This changes it in a range of 0–2 octaves.
Adjusting the amount of LFO e󱐯ect on l-
ter cuto󱐯
①
Turn the
FLTR CO/reverb knob.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The parameter is shown on the display.
• The adjustment range is 0–127.
Adjusting the envelope generator
① Turn the
ATTACK/decay and
RELEASE/sus-
tain knobs.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The parameter is shown on the display.
• To change the decay and sustain, turn the
AT-
TACK/decay and
RELEASE/sustain knobs
while pressing and holding
.
• The adjustment range is 0–127.
• ATTACK, decay and RELEASE can be set in time
ranges of 0–5000 ms.
• The level set by sustain is 0–100%.