Step sequencer playback and recording
15
Step recording
① Press (lights red).
The LED for the current step will blink. The LEDs for
steps that already have notes will light.
② Press
, , , or to select the page. (The
selected page button will light red.)
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The page buttons correspond to the steps as fol-
lows.
Steps 1–16 :
lit green
Steps 17–32 :
lit green
Steps 33–48 :
lit green
Steps 49–64 :
lit green
Steps 65–80 :
lit orange
Steps 81–96 :
lit orange
Steps 97–112 :
lit orange
Steps 113–128 :
lit orange
• Page buttons are enabled or disabled according to
the length of the pattern.
③ Press the step button for the position to input.
The input note sounds, and the step LED blinks.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The
VALUE knob can also be turned to change
the step position. (Step notes will
sound
during
movement).
④ Play a note on the keyboard.
The note of the key pressed sounds (continuously
with sustain).
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• Playing the same note that has already been input
on the step will clear it.
• To input tied notes, while pressing and holding func
, press tie to enable the tie function.
• By pressing a dierent step button while continuing
to hold a keyboard key (changing pages is also pos
-
sible), a tied note can be added that lasts until that
step. (If the same note already exists on the steps
of the tied note, it will be overwritten.)
• While pressing and holding
, press a step
button to delete note and parameter lock data for
that step. (If that step includes a tied note, the en
-
tire tied note will be deleted. It will not be divided.)
• While pressing and holding
, press to
turn sequencer auto step on. When this is on, after
any keyboard key is released, the sequencer will
advance to the next step, and the note on that step
will sound.
• When in overwrite mode, playing keyboard keys will
overwrite notes on steps. (See p.18 “Overwriting
steps while recording (overwrite mode)”.)
• Notes cannot be tied from the last page to the rst
page.
• During tied note input, if a step in a position earlier
than the current step is pressed, it will be reversed.
• The
button can be used even when not
recording.
Recording in real time
① After pressing , press .
② While the pattern is playing back, play the keyboard
at the desired input times.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• If a pre-count has been set, playback will start after
the pre-count. (The pre-count will be shown on the
display.)
• To input tied notes, while pressing and holding
,
press
to enable the tie function.
• When in overwrite mode, playing keyboard keys will
overwrite notes on steps. (See p.18 “Overwriting
steps while recording (overwrite mode)”.)
Directly inputting notes on steps
① Press , , or to select the page.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• During pattern playback, press a page button to
lock to that page. Press
to unlock.
② While pressing the step button that you want to
input a note on, play the keyboard.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• Notes can also be directly input on steps by press-
ing step buttons while playing the keyboard.
• Direct input of notes is not possible during real-time
recording.
• Direct input of notes cannot be used during STUT
-
TER mode.
To Next Page
Loading...
