Sonicware LIVEN 8bit warps - System Settings; Setting Master Tuning; Enabling Function Setting State; Setting Automatic Power Off Function

System settings
27
This section explains settings related to the system.
Explanations assume that the function setting state has
been enabled.
Enabling the function setting state
① Press and hold .
Setting the automatic power o󱐯 function
①
Press
SYSTEM, and select A.PWR.
②
Turn the
VALUE knob to select the automatic
power o󱐯 setting.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• Automatic power o󱐯 has four settings.
1. OFF : Automatic power o󱐯 is disabled.
2. 30 minutes (0.5 on display) : Power will turn o󱐯
automatically after 30 minutes without operation.
3. 1 hour (1H on display) : Power will turn o󱐯 auto
-
matically after 1 hour without operation.
4. 3 hours (3H on display) : Power will turn o󱐯 auto
-
matically after 3 hours without operation.
5. 6 hours (6H on display) : Power will turn o󱐯 auto
-
matically after 6 hours without operation.
• Unsaved data will be cleared when the power turns
o󱐯 automatically. Always save data that is needed.
Setting the battery type
①
Press
SYSTEM, and select BATT.
②
Turn the
VALUE knob to select the type of bat
-
tery.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• Two types of batteries can be selected.
1. Alkaline (ALKL on display)
2. Nickel-metal hydride (NIMH on display)
3. Lithium (LTHM on display)
• The remaining charge shown could be higher than
the actual amount depending on the type of re
-
chargeable battery.
• Please set this correctly because it e󱐯ects opera-
tion time.
Setting the master tuning
①
Press
SYSTEM, and select TUNE.
②
Turn the
VALUE knob to set the master tuning.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The master tuning setting (in cents) will be shown
on the display.
• The adjustment range is － 75–+75.
Setting the clock source
①
Press
CLOCK, and select SRC.
②
Turn the
VALUE knob to set the clock source.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The clock source is shown on the display.
• Four types of clock sources can be selected.
1. INTERNAL (INT on display) : Use LIVEN 8bit
warps internal clock
2. MIDI : Use clock from MIDI
3. SYNC : Use SYNC IN clock
4. LINE IN (LN.IN on display) : Use clock from LINE IN
Setting the polarity of SYNC IN
①
Press
CLOCK, and select S.I.PO.
②
Turn the
VALUE knob to set the clock source.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The clock source is shown on the display.
• Two types of polarity can be selected.
1. FALL : Synchronize with the fall of synchroniza
-
tion signal
2. RISE : Synchronize with the rise of synchroniza
-
tion signal
Setting the polarity of SYNC OUT
①
Press
CLOCK, and select S.O.PO.
②
Turn the
VALUE knob to set the clock source.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The clock source is shown on the display.
• Two types of polarity can be selected.
1. FALL : Synchronize with the fall of synchroniza
-
tion signal
2. RISE : Synchronize with the rise of synchroniza
-
tion signal