Sonicware LIVEN 8bit warps - Waveform Management; Clearing Waveforms; Loading Waveforms; Loading Synth Engine Waveforms (Capture Mode)

Creating and editing waveforms
13
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• Use the
(1–16) and (17–32) buttons to se-
lect pages.
④
Turn the
VALUE knob to set the parameter.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The parameter is shown on the display.
• The adjustment range is － 128 – 127.
⑤ Repeat steps ③ and ④ , and press
.
⑥
Turn the
VALUE knob and select the waveform
number where it will be saved.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The waveform can also be selected by pressing
(U-01–U-16),
(U-17–U-32), (U-33–U-48) or
(U-49–U-64) to select the page, and then pressing
the step button.
• The waveform number (U-number) appears on the
display.
• The selection range is U-01–U-64.
⑧ Press
to save the waveform and end waveform
editing mode.
Clearing waveforms
① Follow steps ① – ④ in “Editing waveforms (easy
mode)”.
② While pressing
, press .
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• All waveform data for the selected waveform num-
ber will be set to 0.
• The waveform can also be edited after this.
• CLR will appear on the display.
Loading waveforms
① Follow steps ① – ④ in “Editing waveforms (easy
mode)”.
② While pressing
, press .
③ Turn the
VALUE knob to select the number of the
waveform to be loaded.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• Waveforms can also be selected by selecting a
page key and pressing a step key. (Pages 1–4 are
preset waveforms and pages 5–8 are user wave
-
forms.)
• The preset waveform name or user waveform num
-
ber (U-number) appears on the display.
• The selection range is preset waveforms 1–63 and
U-01–U-64.
④ Press
to copy the waveform and start waveform
editing mode.
Loading synth engine waveforms
(capture mode)
① While pressing , press
CAPTURE.
②
Turn the
VALUE knob and select the waveform
number where it will be saved.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• Capture mode can only be enabled when the synth
engine is WARP or FM.
• CPTR will appear on the display.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• The waveform can also be selected by pressing
(U-01–U-16),
(U-17–U-32), (U-33–U-48) or
(U-49–U-64) to select the page, and then pressing
the step button.
• The waveform number (U-number) appears on the
display.
• The selection range is U-01–U-64.
③ Press
to return to regular mode.
ーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
• Press
to cancel saving.