Sony BDP-BX2 - 8 Error Log List

To Next Page

To Previous Page

8-1E

BDP-BX2/S360

SECTION 8

ERROR LOG LIST

Category err_code

CSI communication timeout

Mainly ITcon communication error

0x01 csi_id Replace the chip corresponding to the ID, or replace the EMMA3P chip.

Cases where problem occurs

䊶Device for sending only (ex. DAC 2ch/8ch, ES DAC 2ch/8ch device)

䇭Recorded to log during a timeout of the sending complete interrupt

䊶Device for sending and receiving (ex. IFcon device)

䇭Recorded to log during a timeout of the receiving complete interrupt

䊶Other VIDEO_GLUE and HDE specifications are unknown at this time.

䊶ID list (Driver/Common/CSI/if/csi_id_bdp3g_ryoushi.h)

CSI_ID_DAC_2CH = 0, / Audio DAC AK4385A 2ch Write only /

CSI_ID_DAC_8CH = 1, / Audio DAC AK4358 8ch Write only /

CSI_ID_DAC_2CH_ES = 2, / Audio DAC PCM1796 2ch Write only for ES /

CSI_ID_DAC_8CH_ES = 3, / Audio DACs PCM1791A 2ch4 Write only for ES /

CSI_ID_VIDEO_GLUE = 4, / VIDEO Glue for ES /

CSI_ID_HDE1 = 5, / HD Enhancer1 for ES /

CSI_ID_HDE2 = 6, / HD Enhancer2 for ES /

CSI_ID_CC_UCOM = 7, / Spare micro-controller for CC /

CSI_ID_ITCON = 8, 䇭/ ITcon /

I2C communication timeout 0x02 i2c_id Replace the chip corresponding to the ID, or replace the EMMA3P chip.

Cases where problem occurs

䊶Recorded to log during a timeout at sending interrupt standby

䊶ID list (Driver/Common/I2C/if/i2c_id_bdp3g_ryoushi.h)

I2C_ID_HDMI_A = 0, / External HDMI (sub-addrA) SiI9134 /

I2C_ID_HDMI_B = 1, / External HDMI (sub-addrB) SiI9134 /

I2C_ID_SCALER = 2, / 1080p SCALER /

I2C_ID_HDMI_INTERNAL_A = 3, / EMMA3P Internal HDMI I2C-A /

I2C_ID_HDMI_INTERNAL_B = 4, / EMMA3P Internal HDMI I2C-B /

Device ID error for HDMI device 0x03 VendorId DeviceId EMMA fault/External HDMI device fault (for ES)

Read error 0x00 Check for scratches and dust on the disc. Stream or NaviPack read error. Read error for information is not handled.

Wrong region 0x01 Unable to play because of wrong region

Decode error 0x02 Problem with stream This is output by detection of EMMA, and so output may continue for some time.

AACS verify error 0x03 Disc may be invalid. When an error has occurred in ReqAacsPmVerifyUsageHash

Wrong TV system (DVD-Video) 0x04 Disc is invalid. If the TV_system is mixed in the DVD-Video disc, playback stops when mixing is found.

Drive communication error 0x00 opcode Perform ke

eration a

ain. Re

lace if the error occurs a

ain. EMMA error. Perform a s

stem reboot if this occurs.

Drive mechanical error 0x01 opcode Service repair Perform a system reboot if this occurs.

Tray open/close error 0x02 - - - - Perform ke

eration a

ain. Re

lace if the error occurs a

ain. LU error:

(

Disc loadin

error 䋩

Command timeout 0x03 Perform ke

eration a

ain. Re

lace if the error occurs a

ain. Immediate timeout t

e. Perform a s

stem reboot if this occurs.

Shutdown due to overheating of set FAN ERR 0x01

Temperat

ure data

(8bit)

Check the operating temperature environment of the set.

Cases where problem occurs

䊶If the temperature rise results in a thermal shutdown, this is recorded in the log.

No information is available yet in the conversion table between temperature data (8bit) A/D value and

tem

erature data.

FAN breakdown FAN ERR 0x02 Replace the fan.

Cases where problem occurs

䊶When FANDET is used, a fan breakdown dia

nosis b

FANDET is recorded in the lo

NAND Error E7001 0x01

After rebooting, if the error occurs again, or a malfunction occurs, repair by the Service Center is needed.