-
26
Tone
controls:
Low: ±IO dB
at
60
Hz
(XPLOD)
Mid:
±
10
dB at I kHz (XPLOD)
High:
±1O
dB at
10
kHz (XPLOD)
Power
requirements:
12
V DC
car
battery
(negative ground (earth»
Dimensions:
Approx. 178 x 50 x 190
mm
(7 '/8 x 2 x 7 '/8 in)
(wlhld)
Mounting
dimensions:
Approx. 182 x 53 x 163
mm
(7
1
/4
x 2
1
/
8
x 6
1
/2
in)
(wlhld)
Mass:
Approx. 1.7 kg (3
Ib
12
oz)
Supplied
accessories:
Card remote commander:
RM-XI72
Parts for installation and connections
(I
set)
Optional
accessories/equipment:
Rotary commander:
RM-X4S
BUS cable (supplied with an
RCA
pin cord):
RC-61
(I
m), RC-62 (2 m)
CD
changer (10 discs):
CDX-757MX
CD
changer (6 discs): CDX-T69
Source selector: XA-C40
AUX-IN selector: XA-300
USB connection cable for iPod: RC-
lOOIP
HD
Radio™
tuner: XT-lOOHD
Your
dealer
may
not
handle
some
of
the
above
listed
accessories.
Please
ask
the
dealer
for
detailed
information.
Design
and
specifications are subject
to
change
without notice.
• Halogenated flame retardants are not used in the
certain printed wiring boards.
• Halogenated flame retardants are not used in
cabinets.
• Packaging cushions are made from paper.
Troubleshooting
The
following
checklist
will
help
you
remedy
problems
you
may
encounter
with
your
unit.
Before
going
through
the
checklist
below,
check
the
connection
and
operating
procedures.
If
the
problem
is
not
solved,
visit
the
following
support
site.
Support site
http://esupport.sony.com
http://www.xplodsony.com/
No power
is
being supplied
to
the unit.
•
Check
the connection
or
fuse.
•
If
the unit
is
turned
off
and the display disappears, it
cannot be operated with the remote commander.
- Turn on the unit.
The power antenna (aerial) does
not
extend.
The power antenna (aerial) does not have a relay box.
No sound.
•
The
ATI
function is activated,
or
the Telephone
ATI
function (when the interface cable
of
a
car
telephone
is connected to the ATT lead)
is
activated.
•
The
position
of
the fader control
"Fader
& Balance"
is not set for a 2-speaker system.
No beep sound.
•
The
beep
sound is canceled (page 20).
• An optional
power
amplifier is connected and you are
not using the built-in amplifier.
The contents
of
the memory have been erased.
•
The
RESET
button has been pressed.
- Store again into the memory.
• The power supply lead
or
battery has been
disconnected
or
it
is
not connected properly.
Stored stations and correct
time
are erased.
The fuse has blown.
Makes noise when the position
of
the
ignition
is
switched.
The leads are not matched correctly with the
car's
accessory power connector.
During playback
or
reception, demonstration
mode starts.
If
no operation is performed for 5 minutes with
"Demo
on"
set, demonstration mode starts.
- Set
"Demo
off'
(page 20).
The display disappears from/does
not
appear
in the display window.
•
The
dimmer
is
set
"Dimmer
on"
(page 20).
•
The
display disappears
if
you press and hold
(OFF).
- Press and hold
(OFF)
on
the unit until the
display appears.
•
The
connectors are dirty (page 24).
To Next Page
Loading...
