SpeakerCraft MZC-66 Installation Instructions

Page 8 MZC-66 Hardware Installation Instructions
Figure 2
EZ-Pad Features
1. MKP-1.0/MKP-1.1 SOURCE/FUNCTION BUTTONS – Any of this set of eight buttons can be programmed as a
Source Select or transport/function button for the MZC-66. One of the eight must always be designated as a Source
Button. When the system is off, all buttons have a background green color. When a source button is pressed, it turns to
a low-level red color to show the active source and the system is on in that zone. (Backlight Timeout can be set in EZ-
Tools for EZ-Pad and IMKP. MODE 3.1 Backlight is configured in the MODE Keypad Settings Menu.)
2. KEYPAD EXPANSION TERMINAL – This 16-pin header terminal is used to inter-connect the NKP-1.0 and FKP-1.0
EZ-Pad modules for numeric and function key expansion as needed. A ribbon cable is packed with each NKP-1.0 and
FKP-1.0 module for making these connections.
3. ADDRESS SWITCH – An unique hex address must be set for each Master Keypad when connected on a common
bus within a single zone. Unique addresses are not required zone-to-zone (one keypad per zone). It provides up to 16
addresses (0 to F).
EZ-PAD FEATURE DESCRIPTIONS
EZ-Pads come in four basic modules as shown. The MKP-1.0 and MKP-1.1 are Master Keypads and one must be used in each
MZC-66 Zone using a keypad. The MKP-1.1 features a built-in IR receiver and has one less function button than the MKP-1.0,
but are otherwise identical. The NKP-1.0 Numeric and FKP-1.0 Function key modules may be thought of as “slaves” to the
Master Keypad (they will not work alone), providing more buttons for additional numeric and function commands. MKPs,
IMKPs, and MODE 3.1s will all work right out of the box for basic functions such as Source Select /ON, Volume/Mute and
OFF. Confi guration of advanced features and source control requires programming with EZ-Tools.
MKP-1.0 Master
(Not included with MZC-66)
MKP-1.1 Master
(Not included with the MZC-66 and has an IR Receiver)
1.77"
4.07"
Rear View
DVD
SAT
MUTE
iPOD1
CD
PWR
MKP-1.0
J-Box EZ-Pad
- Master -
SpeakerCraft
®
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
KEYPAD EXPANSION
ADDRESS
+RELAY - RELAY
+12V IR/IO GND 485 A 485 B
MUTE
iPOD1
CD
PWR
BASS
TREB
MKP-1.1
J-Box EZ-Pad
w/IRC
- Master -
SpeakerCraft
®
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
KEYPAD EXPANSION
ADDRESS
+RELAY - RELAY
+12V IR/IO GND 485 A 485 B
Rear View
NKP-1.0 Numeric
(Not included with MZC-66)
FKP-1.0 Function
(Not included with MZC-66)
123
456
789
0
TRK DSC
RDM
GRP
PLAY
ESC INFO
MENUGUIDE
FKP-1.0
J-Box EZ-Pad
- Function -
SpeakerCraft
®
KEYPAD EXPANSION
NKP-1.0
J-Box EZ-Pad
- Numeric -
SpeakerCraft
®
KEYPAD EXPANSION
Rear View Rear View
SEL
DVD SAT
CBL
AUX
1234
5
6
7
8
4
9
2
9

SpeakerCraft MZC-66 Specifications

Audio Specifications

rated power per channel	30 Watts, 20 Hz to 20 kHz
power per channel	45 Watts @ 1 kHz
total harmonic distortion	< 0.7 %
frequency response	20 Hz to 20 kHz +/- 1.5 dB
channel separation	> 50 dB @ 10 kHz
crosstalk between sources	> 65 dB @ 10 kHz
signal to noise ratio	> 95 dB

Power

power consumption	55 Watts
line ratings	120 VAC, 2.0A
rear panel fuse	T5AL 250V

Weight and Dimensions

width	17 inches (432 mm)
height	5-1/4 inches (133 mm)
depth	14-3/4 inches (375 mm)
weight	23 lbs (10.5 kg)