ST STM32G070RBT6 - Figure 17. STM32 Nucleo-64 Boards ST Morpho Connector Pinout

44 pages

To Next Page

To Previous Page

UM2324 Rev 4 33/43

UM2324 Connectors

The related pinout and the MCU assignment for the ST morpho connectors are listed in

Figure 17 and Figure Note:.

Figure 17. STM32 Nucleo-64 boards ST morpho connector pinout

Note: ARDUINO

Uno V3 D0 and D1 signals are connected by default on USART1 (MCU I/O PA2

and PA3).

Main Page

Figure 1. STM32 Nucleo-64 Board Top View1
Table of Contents2
Features7
Ordering Information8
Codification8
Table 1. Ordering Information8
Table 2. Codification Explanation8
Development Environment9
System Requirements9
Development Toolchains9
Demonstration Software9
Conventions9
Table 3. ON/OFF Conventions9
Quick Start10
Getting Started10
Hardware Layout and Configuration11
Figure 2. Hardware Block Diagram11
Figure 3. Top Layout12
Figure 4. Bottom Layout12
STM32 Nucleo-64 Board Mechanical Drawing13
Default Board Configuration13
Cuttable PCB13
Table 4. Default Jump Settings13
Figure 5. STM32 Nucleo-64 Board Mechanical Drawing13
Embedded ST-LINK/V2-114
Table 5. ST-LINK Jumper Configuration14
Drivers15
ST-LINK/V2-1 Firmware Upgrade15
Using the ST-LINK/V2-1 to Program/Debug the STM32 on Board15
Figure 6. USB Composite Device15
Using ST-LINK/V2-1 to Program/Debug an External STM32 Application16
Table 6. CN11 Debug Connector (SWD)16
Figure 7. STM32 Nucleo-64 Board Connections Image16
Power Supply and Power Selection17
External Power Supply Input17
Figure 8. ST-LINK Connections Image17
Table 7. Power Supply Capabilities18
Figure 9. STLK Power Source19
Figure 10. JP2 [3-4]: STLK Power Source20
Figure 11. JP2 [5-6]: STLK Power Source21
External Power Supply Output22
Programming/Debugging When the Power Supply Is Not from ST-LINK22
Figure 12. JP2 [7-8]: CHG Power Source22
OSC Clock Sources23
LSE: OSC 32 Khz Clock Supply23
HSE: OSC 8 Mhz Clock Supply24
Reset Sources24
UART2 Communication24
Leds25
Push-Buttons25
Table 8. UART2 Pins25
IDD Measurement26
Jumper Configuration26
Configuration of the Solder Bridges26
Table 9. Jumper Configuration26
Table 10. Solder Bridge Configurations and Settings26
Connectors28
CN2 USB Micro-B Connector28
Table 11. USB Micro-B Pinout28
Figure 13. CN2 USB Micro-B Connector (Front View)28
ARDUINO ® uno V3 Connector29
Figure 14. ARDUINO ® Connectors29
Table 12. ARDUINO ® Connector Pinout30
Figure 15. STM32 Nucleo-64 Boards ARDUINO ® Connector Pinout30
CN7 and CN10 ST Morpho Connectors32
Figure 16. ST Morpho Connectors32
Figure 17. STM32 Nucleo-64 Boards ST Morpho Connector Pinout33
STM32 Nucleo-64 Board Information34
Product Marking34
NUCLEO-G070RB Product History34
Product Identification NUG070RB$AU134
Product Identification NUG070RB$AU234
NUCLEO-G071RB Product History35
Product Identification NUG071RB$AU135
Product Identification NUG071RB$AU235
NUCLEO-G0B1RE Product History35
Product Identification NUG0B1RE$AU135
Board Revision History36
Board MB1360 Revision C-0136
Board MB1360 Revision C-0236
Appendix A STM32 Nucleo-64 Board I/O Assignment37
Table 13. STM32 Nucleo-64 Board I/O Assignment37
Appendix B Federal Communications Commission (FCC) and ISED Canada Compliance Statements39
FCC Compliance Statement39
ISED Compliance Statement40
Appendix Cce Conformity41
Warning41
Simplified Declaration of Conformity41
Table 14. Document Revision History42

ST STM32G070RBT6 - Figure 17. STM32 Nucleo-64 Boards ST Morpho Connector Pinout

Table of Contents

Related product manuals